Directed Electronics READY REMOTE 24927 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 95

background image

25

© 2 0 0 7 D i r e c t e d E l e c t r o n i c s

Safety Shutdown Wires

With all ignition wires properly connected, find the appropriate
safety shutdown wires. These are the brake wire and hood pin
wires.

First locate the factory brake wire using your multimeter. Find the
switch at the top of the metal arm coming off the brake pedal. Use
your vehicle specific wiring information to determine the color of
this wire. With the black lead of your multimeter still in the kick
panel, probe the suspected wire with the red lead of your multi-
meter.

With the brake pedal at reset, the multimeter should read 0 volts.
While watching the multimeter, depress the brake pedal. The
multimeter should read 12 volts. Once you have located the
correct brake wire, solder the small ORANGE wire in the 6-pin
harness to it and wrap the connection with electrical tape.

Installing the hood pin switch requires drilling a hole in a metal
lip under the hood. Choose a location that will allow the pin
switch to be completely depressed when the hood is closed. The
pin switch has a spade connector on the bottom for the wire
connection.

WARNING!

Wear eye protection when drilling.

WARNING!

Do not use the vehicle until you

confirm the operation of the brake shutdown.

WARNING!

These wires are meant to protect the

vehicle and anyone near the vehicle. They MUST
be connected to prevent damage to the vehicle
and possible bodily injury.

«
...
22
23
24
25
26
...
»

Содержание READY REMOTE 24927
































































































Отзывы:

Нет отзывов

Похожие инструкции для READY REMOTE 24927

Бренд: Casablanca Страницы: 5

Бренд: Steren Страницы: 54

966193-0403 - Harmony 890 Advanced Universal Remote Control

Бренд: Logitech Страницы: 25

Бренд: TRACK STAR Страницы: 11

Бренд: Toyota Страницы: 33

Бренд: Kramer Страницы: 18

Бренд: Bosch Страницы: 76

Бренд: Bosch Страницы: 44

Бренд: Bosch Страницы: 16

Бренд: Bosch Страницы: 16

Бренд: Bosch Страницы: 48

Бренд: Bosch Страницы: 2

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 12

EUR511511 guide

Бренд: Panasonic Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды