Directed Electronics READY REMOTE 24927 Скачать руководство пользователя страница 65

Страница: 65 / 95

Last Start Diagnostics:

The system holds in memory the reason for the most recent
remote start activation. To access this report:

Turn the ignition ON and then OFF in less than 5 seconds

Within 5 seconds Press and Release the Momentary
Switch

After 2 seconds the LED will flashpause and repeat 5
times to indicate the cause of the most recent remote
start activation.

Count the LED flashes and consult the Last Start
Diagnostic Chart.

Last Start Diagnostic Chart

LED

Flashes

Description

The Remote Starter has not been activated since the main power
was connected

The Transmitter was used to activate the Remote starter

The Activation Input wire was used to activate the Remote starter

Low temperature activated the Remote Starter in Vacation Mode

Low battery voltage activated the Remote Starter in Vacation Mode

No Diagnostics

Daily Start activated the Remote Starter

Содержание READY REMOTE 24927
































































































Результаты поиска

Содержание READY REMOTE 24927

Отзывы:

Похожие инструкции для READY REMOTE 24927

Бренды по названию

Популярные бренды

Directed Electronics READY REMOTE 24927, Руководство по установке владельца

Результаты поиска

Содержание READY REMOTE 24927

Отзывы:

Похожие инструкции для READY REMOTE 24927

Бренды по названию

Популярные бренды