Directed Electronics READY REMOTE 24927 Скачать руководство пользователя страница 64

Страница: 64 / 95

Remote Start Diagnostics

Remote Start Diagnostics:

Remote Start diagnostics are an important tool to diagnose the
status of the remote start system.

No Start Diagnostics:

If the system fails to activate Remote Start, Quick Stop, Daily
Start or Vacation Mode as expected, the parking lights will flash
to indicate the reason. Consult the No Start Diagnostic Chart.

No Start Diagnostic Chart

Remote Start

Feature

LED

Flashes

Description

Any

Indicates a loss of signal from the transmitter to
the system or a loss of power to the main unit.

Daily Start

The unit is in the Valet Mode or Battery Voltage is
below 11v when attempting to activate this
feature.

Vacation Mode

The unit is in the Valet Mode, Battery Voltage is
below 11v, or the Brake, Hood or Ignition inputs
are active

Remote Start

The unit is in the Valet Mode, Battery Voltage is
below 11v, or the Brake or Hood inputs are active

QuickStop

The unit is in the Valet Mode, Battery Voltage is
below 11v, or the Brake or Hood inputs are active

Содержание READY REMOTE 24927
































































































Результаты поиска

Содержание READY REMOTE 24927

Отзывы:

Похожие инструкции для READY REMOTE 24927

Бренды по названию

Популярные бренды

Directed Electronics READY REMOTE 24927, Руководство по установке владельца

Результаты поиска

Содержание READY REMOTE 24927

Отзывы:

Похожие инструкции для READY REMOTE 24927

Бренды по названию

Популярные бренды