DINGLI S06-E Скачать руководство пользователя | Manualshive

Страница: 70 / 77

background image

OPERATOR’S MANUAL

with Maintenance Information

Maintenance

66

D-2

Replace the Hydraulic Tank Return

Filter Element

DINGLI requires that this procedure be
performed every 1000 hours or annually,
whichever comes first.

Replacement of the hydraulic tank return filter
is essential for good machine performance
and service life. A dirty or clogged filter may
cause the machine to perform poorly and
continued use may cause component damage.
Extremely dirty conditions may require that the
filter be replaced more often.

Beware of hot oil. Contact

with hot oil may cause severe burns.

The hydraulic tank return filter

is mounted on the bracket between the
function manifold and the hydraulic power unit.

1 Clean the area around the oil filter.

Remove the filter with an oil filter wrench.

2 Apply a thin layer of oil to the new oil filter

gasket.

3 Install the new filter and tighten it securely

by hand.

4 Use a permanent ink marker to write the

date and number of hours from the hour
meter onto the filter.

5 Turn the key switch to ground control. Turn

the ground red Emergency Stop button
clockwise to the on position. Pull out the
platform red Emergency Stop button to the
on position.

6 Activate and hold the platform up toggle

switch.

7 Inspect the filter and related components

to be sure that there are no leaks.

8 Clean up any oil that may have spilled.

«
...
68
69
70
71
72
...
»

Содержание S06-E














































































Отзывы:

Нет отзывов

Похожие инструкции для S06-E

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды