DINGLI S06-E Скачать руководство пользователя | Manualshive

Страница: 6 / 77

background image

OPERATOR’S MANUAL

with Maintenance Information

Safety Rules

2

Intended Use

This machine is intended to be used only to lift
personnel, along with their tools and materials
to an aerial work site.

Safety Sign Maintenance

Replace any missing or damaged safety signs.
Keep operator safety in mind at all times. Use
mild soap and water to clean safety signs. Do
not use solvent-based cleaners because they
may damage the safety sign material.

Electrocution Hazard

This machine is not electrically insulated and
will not provide protection from contact with or
proximity to electrical current.

Maintain safe distances from electrical power
lines and apparatus in accordance with
applicable governmental regulations and the
following chart.

Voltage
Phase to Phase

Minimum Safe

Approach Distance

Meters

0 to 300V

Avoid Contact

300V to 50kV

3.05

50kV to 200kV

4.60

200kV to 350kV

6.10

350kV to 500kV

7.62

500kV to 750kV

10.67

750kV to 1000kV

13.72

Allow for platform movement, electrical line
sway or sag and beware of strong or gusty
winds.

Keep away from the machine if it contacts
energized power lines. Personnel on the
ground or in the platform must not touch or
operate the machine until energized power
lines are shut off.

Do not operate the machine during lightning or
storms.

Do not use the machine as a ground for
welding.

Tip-over Hazard

Occupants, equipment and materials must not
exceed the maximum platform capacity or the
maximum capacity of the platform extension.

Maximum capacity – S06-EH

Maximum capacity – S06-E

Maximum occupants (Indoor use) 2

Maximum occupants (Outdoor use) 1

Platform allowable maximum load 230 kg

Extension deck allowable maximum load 113kg

Platform retracted Platform extended

Extension Platform

only only

Work Area Safety

Do not raise the platform unless the machine
is on a firm, level surface.

Do not drive over 0.5 km/h with the platform
raised.

«
...
4
5
6
7
8
...
»

Содержание S06-E














































































Отзывы:

Нет отзывов

Похожие инструкции для S06-E

Бренд: Atlas Equipment Страницы: 71

Бренд: Genie Страницы: 64

Бренд: Genie Страницы: 39

Бренд: Genie Страницы: 43

Бренд: Genie Страницы: 45

Бренд: Genie Страницы: 48

Бренд: Genie Страницы: 50

Бренд: Genie Страницы: 153

Бренд: Genie Страницы: 161

Бренд: Genie Страницы: 182

Бренд: Genie Страницы: 402

Бренд: Genie Страницы: 461

Бренд: Genie Страницы: 497

Бренд: JLG Страницы: 143

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды