DINGLI S06-E страница 40 Скачать руководство пользователя

Страница: 40 / 77

OPERATOR’S MANUAL

with Maintenance Information

Operating Instructions

Battery and Charger Instructions

Observe and Obey:

√

Do not use an external charger or booster

battery.

√

Charge the battery in a well-ventilated area.

√

Use proper AC input voltage for charging

as indicated on the charger.

√

Use only a Dingli authorized battery and

charger.

To Charge Battery

1 Be sure the batteries are connected before

charging.

2 Open the battery compartment. The

compartment should remain open for the
entire charging cycle.

Maintenance - free battery

3 Connect the battery charger to a grounded

AC circuit.

4 The charger will indicate when the battery

is fully charged.

Standard Battery

5 Remove the battery vent caps and check

the battery acid level. If necessary, add
only enough distilled water to cover the
plates. Do not overfill prior to the charge
cycle.

6 Replace the battery vent caps.

7 Connect the battery charger to a grounded

AC circuit.

8 The charger will indicate when the battery

is fully charged.

9 Check the battery acid level when the

charging cycle is complete. Replenish with
distilled water to the bottom of the fill tube.
Do not overfill.

Dry Battery Filling and

Charging Instructions

1 Remove the battery vent caps and

permanently remove the plastic seal from
the battery vent openings.

2 Fill each cell with battery acid (electrolyte)

until the level is sufficient to cover the
plates.

Do not fill to maximum level until the battery
charge cycle is complete. Overfilling can
cause the battery acid to overflow during
charging. Neutralize battery acid spills with
baking soda and water.

3 Install the battery vent caps.

4 Charge the battery.

5 Check the battery acid level when the

charging cycle is complete. Replenish with
distilled water to the bottom of the fill tube.
Do not overfill.

Содержание S06-E














































































Результаты поиска

Содержание S06-E

Отзывы:

Похожие инструкции для S06-E

Бренды по названию

Популярные бренды

DINGLI S06-E, Руководство оператора с информацией по обслуживанию

Результаты поиска

Содержание S06-E

Отзывы:

Похожие инструкции для S06-E

Бренды по названию

Популярные бренды