DINGLI S06-E Скачать руководство пользователя | Manualshive

Страница: 10 / 77

background image

OPERATOR’S MANUAL

with Maintenance Information

Safety Rules

6

Conduct a thorough pre-operation inspection
of the machine and test all functions before
each work shift. Immediately tag and remove
from service a damaged or malfunctioning
machine.

Be sure all maintenance has been performed
as specified in this manual

Be sure all decals are in place and legible.

Be sure the operator’s manual is complete,
legible and in the storage container located in
the platform.

Bodily Injury Hazard

Do not operate the machine with a hydraulic oil
or air leak. An air leak or hydraulic leak can
penetrate and/or burn skin.

Improper contact with components under any
cover will cause serious injury. Only trained
maintenance personnel should access
compartments. Access by the operator is only
advised when performing a pre-operation
inspection. All compartments must remain
closed and secured during operation.

Battery Safety

Burn Hazard

Batteries contain acid. Always wear protective
clothing and eye wear when working with
batteries.

Avoid spilling or contacting battery acid.
Neutralize battery acid spills with baking soda
and water.

Explosion Hazard

Keep sparks, flames and lighted tobacco away
from batteries. Batteries emit explosive gas.

The battery tray should remain open during
the entire charging cycle.

Do not contact the battery terminals or the
cable clamps with tools that may cause
sparks.

Component Damage Hazard

Do not use any battery charger greater than
24V to charge the batteries.

Electrocution/ Burn Hazard

Connect the battery charger
to a grounded, AC 3-wire
electrical outlet only.

Inspect daily for damaged
cords, cables and wires.
Replace damaged items

before operating.

Avoid electrical shock from contact with
battery terminals. Remove all rings, watches
and other jewelry.

Tip-over Hazard

Do not use batteries that weigh less than the
original equipment. Batteries are used as
counterweight and are critical to machine
stability. Each battery must weigh 26 kg. The
batteries must weigh a minimum of 104 kg.

Lifting Hazard

Use the appropriate number of people and
proper lifting techniques when lifting batteries.

«
...
8
9
10
11
12
...
»

Содержание S06-E














































































Отзывы:

Нет отзывов

Похожие инструкции для S06-E

Бренд: Pramac Страницы: 121

Genie S-45 Trax

Бренд: Terex Страницы: 17

Бренд: Happ Страницы: 31

Бренд: Launch Страницы: 15

Бренд: TIGIEFFE Страницы: 124

Бренд: Mitsubishi Страницы: 21

Бренд: Mitsubishi Страницы: 22

Бренд: JLG Страницы: 214

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды