DINGLI S06-E Скачать руководство пользователя | Manualshive

Страница: 64 / 77

background image

OPERATOR’S MANUAL

with Maintenance Information

Maintenance

60

Level sensor

28 Move the machine onto a grade which

exceeds the rating of the level sensor.
Refer to the serial label on the machine.

29 Press the lift function select button.

Standing on the up-hill side of the machine,
attempt to raise the platform to
approximately 2 m.

⊙

Result: The LED readout screen shows

code LL, an alarm sounds, and the
machine stops lifting after the pothole
guards are deployed. The machine is
functioning properly.

¤

Result: The LED readout screen does not

show code LL, the alarm does not sound
and the machine will continue to lift the
platform after the pothole guards are
deployed. Adjust or replace the level
sensor.

30 Press the drive function select button.

Standing on the up-hill side of the machine,
attempt to steer and drive the machine.

⊙

Result: The LED readout screen shows

code LL, an alarm sounds, and the
machine will not steer or drive. The
machine is functioning properly.

¤

Result: The LED readout screen does not

show code LL, the alarm does not sound
and the steer and drive functions operate.
Adjust or replace the level sensor.

Pothole Limit Switches

31 Lower the platform to the stowed position.

Move the machine onto a firm, level
surface.

32 Place a wooden block approximately 5 cm

tall under the right pothole guard.

33 Press the lift function select button.

Attempt to raise the platform
approximately 2m.

⊙

Result: The pothole guard contacts the

block and does not fully deploy, the LED
readout screen shows code 18, an alarm
sounds and the platform will lift to 2m or
beyond. The machine is functioning
properly.

¤

Result: The pothole guard contacts the

block and does not fully deploy, the LED
readout screen does not show code 18, the
alarm does not sound and the machine will
continue to lift the platform after the pothole
guards are deployed. Adjust or replace the
pothole limit switch.

34 Press the drive function select button.

Attempt to steer or drive the machine.

⊙

Result: The LED readout screen shows

code 18, an alarm sounds, and the
machine will not steer or drive. The
machine is functioning properly.

¤

Result: The LED readout screen does not

show code 18, the alarm does not sound
and the steer and drive functions operate.
Adjust or replace the down limit switch.

35 Lower the platform to the stowed position

and remove the block under the right
pothole guard.

36 Repeat this procedure beginning with step

32 for the left pothole guard.

37 Lower the platform to the stowed position,

remove the block under the left pothole
guard.

38 Turn off the machine.

«
...
62
63
64
65
66
...
»

Содержание S06-E














































































Отзывы:

Нет отзывов

Похожие инструкции для S06-E

Бренд: XLT Systems Страницы: 22

Бренд: Snorkel Страницы: 108

Бренд: Snorkel Страницы: 155

Бренд: Terex Страницы: 125

Бренд: Terex Страницы: 140

Бренд: Terex Страницы: 282

Бренд: DINGLI Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды