DINGLI BA14J-AWD Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 97

background image

Operation & Maintenance Manual

Section5-Operation Instruction

Dingli Machinery

5-5

5.3

Engine Operation

NOTE:

Initial starting should always be performed from the Ground Control station.

IF  ENGINE  FAILS  TO  START  PROMPTLY,  DO  NOT  CRANK  FOR  AN
EXTENDED  TIME.  SHOULD  ENGINE  FAIL  TO  START  AGAIN,
ALLOW  STARTER  TO  “COOL  OFF”  FOR  2-3  MINUTES.  IF  ENGINE
FAILS

AFTER

SEVERAL

ATTEMPTS,

REFER

TO

ENGINE

MAINTENANCE MANUAL.

NOTE: Diesel engines only: After turning on ignition, operator must wait until glow
plug indicator light goes out before cranking engine.

Starting Procedure

1)

Turn key of SELECT switch to GROUND. Position POWER/EMERGENCY STOP

switch to ON, then push the ENGINE START switch until engine starts.

ALLOW ENGINE TO WARM-UP FOR A FEW MINUTES AT LOW
SPEED BEFORE APPLYING ANY LOAD.

2)

After engine has had sufficient time to warm up, shut engine off.

3)

Turn SELECT switch to PLATFORM.

4)

From Platform, pull POWER/EMERGENCY STOP switch out, then push the ENGINE
START switch until engine starts.

NOTE: Footswitch must be in released (up) position before starter will operate. If starter
operates with footswitch in the depressed position, DO NOT OPERATE MACHINE.

Shutdown Procedure

IF AN ENGINE MALFUNCTION CAUSES AN UNSCHEDULED
SHUTDOWN, DETERMINE THE CAUSE AND CORRECT IT BEFORE
RESTARTING THE ENGINE

.

1)

Remove all loads and allow engine to operate at low speed for 3-5 minutes; this allows
further reduction of internal engine temperature.

2)

Push POWER/EMERGENCY STOP switch in.

3)

Turn MASTER switch to Off.

Refer to Engine Manufacturer’s manual for detailed information.

«
...
56
57
58
59
60
...
»

Содержание BA14J-AWD


































































































Отзывы:

Нет отзывов

Похожие инструкции для BA14J-AWD

Бренд: OMA Страницы: 75

Бренд: gala gar Страницы: 42

Бренд: M-system Страницы: 5

Бренд: Jäckie Страницы: 48

Laron BL digital

Бренд: BAK Thermoplastic Welding Technology Страницы: 13

Бренд: WAGO Страницы: 82

Бренд: TECO Страницы: 39

Бренд: Kaye Страницы: 168

Бренд: ANDELI Страницы: 23

Бренд: Gude Страницы: 40

Бренд: Elettro CF Страницы: 44

Бренд: stertil Страницы: 39

Lift Guard GRC-12

Бренд: Genie Страницы: 117

Бренд: Roger Technology Страницы: 8

Бренд: Valeo Страницы: 12

SC600 Revo Global

Бренд: Valeo Страницы: 12

Бренд: Valeo Страницы: 86

Бренд: Valco baby Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды