DINGLI BA14J-AWD Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 97

background image

Operation & Maintenance Manual

Section5-Operation Instruction

Dingli Machinery

5-6

5.4 Traveling (Driving) Operation

DO NOT DRIVE WITH BOOM  EXTENDED OR ABOVE HORIZONTAL
EXCEPT ON A SMOOTH, FIRM AND LEVEL SURFACE.

TO  AVOID  LOSS  OF  TRAVEL  CONTROL  OR  “TIP  OVER”,  DO  NOT
DRIVE MACHINE ON GRADES EXCEEDING THOSE SPECIFIED ON
THE  SERIAL  NUMBER  TAG  OR  AS  NOTED  IN  THE  OPERATORS
MANUAL.

DO NOT DRIVE ON SIDESLOPES WHICH EXCEED 5 DEGREES.

USE  EXTREME  CAUTION  WHEN  DRIVING  IN  REVERSE  AND  AT
ALL TIMES WHEN THE PLATFORM IS ELEVATED.

TRAVEL  GRADES  WITH  DRIVE  SPEED/TORQUE  SELECT  SWITCH
IN  THE  FORWARD  POSITION.  USE  CAUTION  WHEN  DRIVING  IN
REVERSE  AND  WHEN  DRIVING  WITH  PLATFORM  ELEVATED,
ESPECIALLY  WHEN  DRIVING  WITH  ANY  PART  OF  MACHINE
WITHIN 6 FEET (2 M) OF AN OBSTRUCTION.

BEFORE DRIVING, MAKE SURE BOOM IS POSITIONED OVER REAR
DRIVE  AXLE.  IF  BOOM  IS  OVER  FRONT  WHEELS,  STEER  AND
DRIVE CONTROLS WILL BE REVERSED.

LEVEL

Traveling Forward and Reverse

1)

With the engine running, activate footswitch.

2)

Position Drive controller to FORWARD or REVERSE as desired.

DO NOT DRIVE THE MACHINE ON GRADES AND SIDESLOPES

EXCEEDING THOSE SPEICIFIED ON THE TECHNICAL SPECIFICATION

«
...
57
58
59
60
61
...
»

Содержание BA14J-AWD


































































































Отзывы:

Нет отзывов

Похожие инструкции для BA14J-AWD

Бренд: HandyTrac Страницы: 14

Бренд: Laser Страницы: 2

OneFlow OFTWH-R

Бренд: Watts Страницы: 8

Бренд: Perma Страницы: 26

Gator Grip Drum EGG-1

Бренд: Wesco Страницы: 2

Бренд: Welding Industries Malaysia Страницы: 20

Air-Cooled Automatics ACAPTS-1.0

Бренд: Bernard Страницы: 4

MIG/MAG Welding Machine MIG/MAG 301 E

Бренд: Elektra Beckum Страницы: 36

Бренд: National Instruments Страницы: 13

Бренд: GRS Страницы: 4

Бренд: Lincoln Electric Страницы: 35

Eagle 2000A Series

Бренд: Rapid Packaging Страницы: 41

TIG-300PI AC/DC

Бренд: Taurus Страницы: 26

Бренд: Taurus Страницы: 35

Бренд: Taurus Страницы: 21

MICHELANGELO BT A 60

Бренд: BFT Страницы: 84

Бренд: Fieldmann Страницы: 20

Бренд: Lincoln Electric Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды