DINGLI BA14J-AWD Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 97

background image

Operation & Maintenance Manual

Section3-User Responsibility, Machine

Preparation, and Inspection

Dingli Machinery

3-2

necessary inspections have been completed successfully before placing the machine into
service. These procedures will aid in obtaining maximum service life and safe operation.

The following table covers the periodic machine inspections and maintenance recommended
by Dingli Machinery Co, Ltd. Consult local regulations for further requirements for aerial
work platforms. The frequency of inspections and maintenance must be increased as
necessary when the machine is used in a harsh or hostile environment, if the machine is used
with increased frequency, or if the machine is used in a severe manner.

Table 3-1.Inspection and Maintenance Table

Type

Frequency

Primary

Responsibility

Reference

Pre-Start
Inspection

Before using each day;
or whenever there’s an
Operator change.

User or
Operator

Operator and Safety Manual

Pre-Delivery
Inspection

Before each sale, lease,
or rental delivery.

Owner, Dealer,
or User

Operation and Maintenance
Manual and applicable Dingli
Inspection Form

Frequent
Inspection

In service for 3 months
or 150 hours, whichever
comes first; or Out of
service for a period of
more than 3 months; or
Purchased used.

Owner, Dealer,
or User

Operation and Maintenance
Manual and applicable Dingli
Inspection Form

Annual
Machine
Inspection

Annually, no later than
13 months from the date
of prior inspection.

Owner, Dealer,
or User

Operation and Maintenance
Manual and applicable Dingli
Inspection Form

Preventative
Maintenance

At intervals as specified
in the Operation &
Maintenance Manual

Owner, Dealer,
or User

Operation and Maintenance
Manual and applicable Dingli
Inspection Form

SINCE THE MACHINE MANUFACTURER HAS NO DIRECT
CONTROL OVER THE FIELD INSPECTION AND MAINTENANCE,
SAFETY IS THE RESPONSIBILITY OF THE OWNER/OPERATOR

.

3.2.2 Preparation for Use

Before a new machine is put into operation it must be carefully inspected for any evidence of
damage resulting from shipment and inspected periodically thereafter, as outlined in Delivery
and Frequent Inspection (see section 3.2.3). During initial start-up and run, the unit should be

«
...
23
24
25
26
27
...
»

Содержание BA14J-AWD


































































































Отзывы:

Нет отзывов

Похожие инструкции для BA14J-AWD

Бренд: bar Страницы: 2

Бренд: VENCO Страницы: 4

MODULEX EXT Series

Бренд: Unical Страницы: 52

Бренд: Omniflex Страницы: 2

Бренд: gala gar Страницы: 28

Бренд: Roger Страницы: 2

Бренд: Wesco Страницы: 20

Бренд: GYS Страницы: 24

Бренд: Feig Electronic Страницы: 21

Бренд: Miller Страницы: 44

Бренд: Zepro Страницы: 6

2200 Traditional Series

Бренд: Zephir Страницы: 2

Compact 220 AC/DC

Бренд: Helvi Страницы: 108

Бренд: WARPP Страницы: 19

VANTAGE SVM178-B

Бренд: Lincoln Electric Страницы: 278

Бренд: Reechcraft Страницы: 56

ACCOLIFT series

Бренд: ACCO Brands Страницы: 140

Roughneck C-4015S

Бренд: Miller Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды