The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confidential. Any disclosure, copying, distribution to third
party is strictly prohibited.
40
276
Chronometer shown as 9959? (if not: 9-59)
- Should the time of the chronometer be shown as 9959 on the secondary display? If not, it will be shown as 9-59. So,
practically the dash is sacrificed for gaining another digit of the chronometer. The allowed answer is either: 0 (No: 9-59) or: 1 (Yes: 9959).
No / Yes
277
Chronometer shows minutes ? (if not: seconds)
- Should the chronometer show minutes on the secondary display? If not, it will show seconds.
The allowed answer is either:
0 (No: seconds) or: 1 (Yes: minutes).
No / Yes
278
Show clock/year for 5 seconds with K3/K4? -
If this question is enabled and key K3 is pressed then the clock will be shown on the secondary display and the date
on the main display for 5 seconds. With this question enabled and key K4 is pressed then the year will be shown on the main display for 5 seconds. This question is
only meaningful if the visualization of the clock has been disabled with Q.268. The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
279
Disable Password for manual clock Setting?
Yes = clock edit cannot be enabled by password.
No / Yes
280
Are Time/Dist Units programmed as Money Values?
If Yes, then time unit (Q5,Q6,Q7) and distance unit (Q2,Q3,Q4) are programmed in money, else are as usual
seconds and meters (or yards)
No / Yes
281
Percentage Discount should exclude Extras?
When a Percentage Discount is applied, should it be applied also to extras or only to fare amount?
No / Yes
282
Put off displays in ForHire after time of Q.283?
–
If yes then in ForHire the displays will be put off after the time established in Q.283.
See also Q.283. The allowed answer is either:
0 (No) or: 1 (Yes).
No / Yes
283
Stand-by time in Hired and Stopped:
in Hired and Stopped this is the time after which the taximeter will go in stand-by. In stand-by the internal functions are all active
but the display is put OFF. The taximeter is 'woken-up' by either pressing any key or by the first pulse from the transducer. The time is given in minutes with an accuracy
of 1 minute. The allowed value goes from 0 (min) to 255 (max).
0 - 255 minutes
284
Shut-down time in ForHire:
in ForHire this is the time after which the taximeter will be shut-down. In shut-down all internal functions except the clock are deactivated
and also the display is put OFF. The taximeter is 'woken-up' by either pressing the OP key or by the first pulse from the transducer. Also see Q.192. If the answer is 0
the taximeter doesn't switch-off automatically anymore. Is this case it can only be switched-off manually by pressing in For-Hire position K2 and K4 together. The time is
given in minutes with an accuracy of 1 minute. The allowed value goes from 0 (min) to 255 (max).
0 - 255 minutes
285
Time of displaying total cost
: this is the time during which the total cost will be shown on the primary display in Stopped. Initially, in Hired the primary display shows
the accumulated fare cost and the secondary display shows the extra-charge. Upon entering Stopped the secondary display goes OFF and the primary display shows
the total cost (the sum) for the time programmed here. After this time both displays show their original data again. The time is given in seconds with an accuracy of 1
second. The allowed value goes from 0 (min) to 255 (max). The value of 0 disables this function. Between 1 and 254 the Time sum is in seconds. In case of a value of
255 this function becomes manual at the first attempt Sum at the second releases the Sum.
0 - 255
286
Restart time in Hired or Stopped without power
: if the power is removed from the taximeter while in Hired or in Stopped then this is the time after which the fare-cost
will be discarded and the taximeter will restart in Stopped. The time is given in seconds with an accuracy of 1 second. The allowed value goes from 0 (min) to 255 (max).
0
-
255
seconds
287
When the taximeter show the Sum, does any key pressed release the Sum?
If yes and the sum is active in Stopped, then pressing any key release the sum.
No / Yes
288
How to show a Prog-Date cost increment? -
If the unit-cost and/or the initial cost gets incremented by any Prog-Date should the proportional part be shown separately
on the secondary display? If not, the proportional part will be summed directly with the fare-cost shown on the primary display.
The allowed answer is either:
0 (No: show summed) or: 1 (Yes: show separately).
0= summed
1= separately
289
Enable the summing of extra-charges also in Hired? -
Should it be possible to sum the extra-charges manually with key K4 also in Hired?
The allowed answer is either:
0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
290
Sum extra charges right from the start of the fare? -
Should the extra-charges be summed with the (initial) cost of the fare right from the start of the fare ? If not, the
extra-charges will be displayed on the secondary display. The allowed answer is either: 0 (No: sec. disp.) or: 1 (Yes: summed).
No / Yes
291
If from Hired to Stopped sum extra-charges automatically? -
Should the extra-charges be summed automatically upon going from Hired to Stopped ?
If not, the extra-charges can be summed by pressing key K4. The allowed answer is either: 0 (No: manually) or: 1 (Yes: automatically).
No / Yes
292
After summing extra-charges inhibit other e.-c.? -
Once the extra-charges have been summed should it be impossible to sum other extra-charges?
The allowed answer is either:
0 (No: sum others) or: 1 (Yes: inhibited).
No / Yes
293
On impulse split the fare-cost?
- As soon as an impulse is received should the total fare-cost be split into fare-cost and extra-charges?
The allowed answer is either:
0 (No: no split) or: 1 (Yes: split).
No / Yes
294
Cancel all manual extra-charges in this block? -
Should all manual extra-charges in this block be cancelled?
The allowed answer is either:
0 (No: maintain) or: 1 (Yes: cancel).
No / Yes
VAT
295
The percentage of VAT:
this is the tax-percentage of VAT; for example: 18.5 %. The percentage is given in numbers with an accuracy of 0.1 percent. The allowed value
goes from 0 (min) to 65535 (max). For example: use 185 for programming a VAT of 18.5 %.
0 - 65535
296
The distance for enabling the VAT function:
this is the distance after which the VAT function will be enabled. The distance is given in metres with an accuracy of 0.1
meter. The allowed value goes from 0.0 (min) to 6553.5 (max). The digit indicating multiples of 0.1 m (so at the right of the decimal point) will flash.
0 - 65535
297
The fare-cost for enabling the VAT function: t
his is the total accumulated fare-cost at which the VAT function will be enabled. The cost is given in the local currency
with an accuracy of 1. The allowed value goes from 0 (min) to 65535 (max).
0 - 65535
PRINTER
298
Number of tickets with cash payment
: this is the number of tickets that should be printed if the client pays with cash.
The number of tickets is given in whole numbers. The allowed value goes from 0 (min) to 65535 (max).
0 - 65535
299
Number of tickets with corporate credit card: t
his is the number of tickets that should be printed if the client pays with a corporate credit card. The number of tickets
is given in whole numbers. The allowed value goes from 0 (min) to 65535 (max).
0 - 65535
300
Number of tickets with commercial credit card:
this is the number of tickets that should be printed if the client pays with a commercial credit card. The number of
tickets is given in whole numbers. The allowed value goes from 0 (min) to 65535 (max).
0 - 65535
301
Number of tickets with prepaid credit card:
this is the number of tickets that should be printed if the client pays with a prepaid credit card. The number of tickets is
given in whole numbers. The allowed value goes from 0 (min) to 65535 (max).
0 - 65535
