The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confidential. Any disclosure, copying, distribution to third
party is strictly prohibited.
38
214
The taxi-light must go ON in overspeed?
- If Yes then the taxi-light will go ON in case the actual velocity is higher than the velocity programmed in Q.200. The allowed
answer is either:
0 (No: OFF) or: 1 (Yes: ON).
No / Yes
215
Taxi-light must go on overspeed?
No / Yes
from Q 216 / available for any possible software extension / to Q 218
219
Taxi-light ON in this tariff-block? -
With Yes the taxi-light will go ON in the corrisponding tariff-block.
The allowed answer is either:
0 (No: OFF) or: 1 (Yes: ON).
No / Yes
220
Block-number for taxi-light to be ON:
this is the number of the tariff-block where the taxi-light should be ON. The allowed value goes from 0 (min) to 62 (max).
0 - 62
221
Prog-Date-number for taxi-light to be ON:
this is the number of the Prog-Date where the taxi-light should be ON. The allowed value goes from 0 (min) to 8 (max).
0 - 8
222
State of taximeter for taxi-light to be ON
- This is the state (or states) of the taximeter in which the taxi-light should be ON.
The allowed values are:
0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
Also combinations are allowed. In that case the values need to be summed together.
For example, to put ON the taxi-light in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
For Hire = 128
Stopped = 64
Hired = 32
None = 0
LIGHT N. 1
223
Enable light n. 1 ON in day-time?
- Should it be possible for light number 1 to be ON during the day-time?
The allowed answer is either:
0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
224
Light n. 1 must flash? -
If Yes light number 1 will flash. The allowed answer is either: 0 (No: no flash) or: 1 (Yes: flash).
No / Yes
225
Light n. 1 must go ON in overspeed? -
If Yes then light number 1 will go ON in case the actual velocity is higher than the velocity programmed in Q.200. The allowed
answer is either:
0 (No: OFF) or: 1 (Yes: ON).
No / Yes
226
Light n. 1 must go on below overspeed?
No / Yes
227
The light n.1 is used a Buzzer output ?
If Yes then the light N.1 will go ON for a short time in case a buzzer beep is programmed (Q338, Q339, Q340)
No / Yes
228
The Light n.1 must go ON if the shift is Open?
If Yes then the Light n.1 will go ON in case the shift is OPEN
No / Yes
229
Available for future extensions
No / Yes
230
Light n. 1 ON in this tariff-block?
- With Yes light number 1 will go ON in the corrisponding tariff-block.
The allowed answer is either:
0 (No: OFF) or: 1 (Yes: ON).
No / Yes
231
Block-number for light n. 1 ON:
this is the number of the tariff-block where light number 1 should be ON.
The allowed value goes from 0 (min) to 62 (max).
0 - 64
232
Prog-Date-number for light n. 1 ON:
this is the number of the Prog-Date where light number 1 should be ON.
The allowed value goes from 0 (min) to 8 (max).
0 - 8
233
State of taximeter for light n. 1 ON:
this is the state (or states) of the taximeter in which the light number 1 should be ON.
The allowed values are:
0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
Also combinations are allowed. In that case the values need to be summed together.
For example, to put ON light number 1 in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
For Hire = 128
Stopped = 64
Hired = 32
None = 0
LIGHT N. 2
234
Enable light n. 2 ON in day-time?
Should it be possible for light number 2 to be ON during the day-time?
The allowed answer is either:
0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
235
Light n. 2 must flash?
- If Yes light number 2 will flash. The allowed answer is either: 0 (No: no flash) or: 1 (Yes: flash).
No / Yes
236
Light n. 2 must go ON in overspeed?
- If Yes then light number 2 will go ON in case the actual velocity is higher than the velocity programmed in Q.200. The allowed
answer is either:
0 (No: OFF) or: 1 (Yes: ON).
No / Yes
237
Light n. 2 must go on below overpseed?
No / Yes
238
The light n.2 is used a Buzzer output ?
If Yes then the light N.2 will go ON for a short time in case a buzzer beep is programmed (Q338, Q339, Q340)
No / Yes
239
The Light n.2 must go ON if the shift is Open?
If Yes then the Light n.2 will go ON in case the shift is OPEN
No / Yes
240
Available for future extensions
No / Yes
241
Light n. 2 ON in this tariff-block?
- With Yes light number 2 will go ON in the corrisponding tariff-block. The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
No / Yes
242
Block-number for light n. 2 ON:
this is the number of the tariff-block where light number 2 should be ON. The allowed value goes from 0 (min) to 62 (max).
0 - 62
243
Prog-Date-number for light n. 2 ON:
this is the number of the Prog-Date where light number 2 should be ON. The allowed value goes from 0 (min) to 8 (max).
0 - 8
244
State of taximeter for light n. 2 ON:
this is the state (or states) of the taximeter in which the light number 2 should be ON.
The allowed values are:
0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
Also combinations are allowed. In that case the values need to be summed together.
For example, to put ON light number 2 in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
For Hire = 128
Stopped = 64
Hired = 32
None= 0
LIGHT N. 3
245
Enable light n. 3 ON in day-time?
- Should it be possible for light number 3 to be ON during the day-time?
No / Yes
