Digital Aquatics ReefKeeper Lite, Руководство пользователя

Страница: 20 / 30

34
ReefKeeper Lite User Guide
Programming
5 Press the [Up] or [Down] buttons to make your selection and press [Enter] to confi rm.
The next prompt is for setting the default state for the output. If the programmed module
can no longer communicate with the head unit, the module will set the output to the state
chosen in the default setting. For example, if a heater is plugged into channel 1 on a PC4
and it can no longer communicate with the head unit, the default state will take aff ect.
5 Press the [Up] or [Down] buttons to choose between the “On” and “Off ” options.
The screen will change and show “Save”.
6 Press the [Enter] button to save.
You can go back from a save by pressing [Back] when save is fl ashing.
To set up the Controller Function using a channel or other output Device
1 From a Module’s Port Menu, select “Function” and press [Enter] .
2 Press the [Up] or [Down] buttons to scroll to “Controller” and press [Enter]
The fi rst prompt will be for “Device” with “None” fl ashing.
3 Press the [Up] or [Down] buttons to select the probe or device that will trigger the
control function and press [Enter] to confi rm.
The next prompt will be for “On When”. Options are “On” or “Off ”.
When the control function is set to be on “On” the output will be powered when the device’s
value is ON.
When the control function is set to be on “Off ” the output will be powered when the device’s
value is OFF.
4 Press the [Up] or [Down] buttons to set this fi eld and press [Enter] to confi rm.
The next prompt will be for “In Standby” with the options of On/Off /Ignore. This sets the
state of the output when you enter Standby mode on the head unit
5 Press the [Up] or [Down] buttons to make your selection and press [Enter] to confi rm.
ReefKeeper Lite User Guide
35
Programming
The next prompt is for setting the default state for the output. If the programmed module
can no longer communicate with the head unit, the module will set the output to the state
chosen in the default setting. For example, if a heater is plugged into channel 1 on a PC4
and it can no longer communicate with the head unit, the default state will take aff ect.
6 Press the [Up] or [Down] buttons to choose between the “On” and “Off ” options.
The screen will change and show “Save”.
7 Press the [Enter] button to save.
You can go back from a save by pressing [Back] when save is fl ashing.
Pump (Other)
Similar to WaveMaker, the Pump (Other) function allows for advance pump setup without linking
the pump to the oscillating wavemaker function.
To set up the Pump (Other) function
1 From a Module’s Port Menu, select “Function” and press [Enter] .
2 Press the [Up] or [Down] buttons to scroll to “Pump (Other)” and press [Enter]
The fi rst prompt will be for “Night Mode” with the default “Off ” fl ashing. It’s common to
turn off some powerheads at night to allow for a calming aff ect in the tank
3 Press the [Up] or [Down] buttons to set the output to be “On” or “Off ” during the
programmed Night Mode.
4 Once the fi eld is set press [Enter] to confi rm.
The next prompt will be for “In Standby” with the options of On/Off /Ignore. This sets the
state of the output when you enter Standby mode on the head unit.
5 Press the [Up] or [Down] buttons to make your selection and press [Enter] to confi rm.
The next prompt will be for “Standby Delay” time with 00:00:00 and the fi rst fi eld (hour) will
be fl ashing.
6
Press the [Up] or [Down] buttons to set the fi rst fi eld (hour), press [Enter] to set and
move to the next fi eld.
7 Once the value is set press [Enter] to confi rm.