Deutz EMR 2 Скачать руководство пользователя страница 16

1

2

3

4

5

6

7

8

9

10

11

12

12

Seite 74

© 06/02

EMR 2

System Functions

4.3

Speed control

Provision is made for various variations of speed control that must be programmed in advance (at the end
of the programming) depending on the application case (power generation, building or agricultural machi-
nes) and usage conditions. The variations depend on the type of programmed and the selected functions.

The following types of speed regulation (switches) are optional and are programmed at the works depen-
ding on the variant (pin assignment see Chapter 6.1):

Function

Variant

Description

Remarks

Variable speed
control

Variable speed 

governor

1)

1) Types of speed control

Variable speed control

For this type of control the speed of the engine is governed or kept constant with reference to the desired speed of revolution.
For changes of load, the new required amount of fuel is set in accordance with a PID control. The desired value can be
determined through various variants. 

Min/Max control

For this type of control, the fuel injection quantity is determined on the basis of the desired value. the result of this is that, for
this type of control, a speed of revolution depending on the load situation is set. The idling (= Minimum) and the end
revolutions (= Maximum) are controlled taking into account the control parameter speed droop 1 and speed droop 2. The
basis for this type of control is the drive characteristic field.

Pure variable speed governor without addi-
tion and switch-over functions

Only one vari-
ant can be 
selected

Fixed speed governor Variable speed governor with fixed, pre-defi-

ned speed for gensets (1,500 or 1,800 rpm), 
desired speed of rotation is defined in the 
scope of customer supply (KLU).

Change-over 
switching speed 1 / 

2

2)

2) Change-over switching see point 4.3.1.

Variable speed governor with change-over 
switching possibility between two speeds.

Change-over swit-
ching speed fixed/

variable

2)

Variable speed governor with change-over 
switching possibility between a fixed pro-
grammed and a variable speed of revolution.

Speed variable /

freeze

2)

Variable speed governor with change-over 
switching possibility between:
freezing a current desired speed as set point 
independent of the pedal setting, and a varia-
ble revolution.

Speed memory
function

Customer-specific solution for storing and 
calling up two speeds of revolution.

Genset
applications

Power generation
governor with adju-
stable speed range

As for change-over switching fixed/variable 
speed. 

Without Load

 the speed can be adju-

sted in the speed range.

See also 
system des-
cription 
EMR Genset, 
TN 0297 9939

Power generation for 
network synchronisa-
tion or Load distribu-
tion

As for change-over switching fixed/variable 
speed. The variable revolutions can be adju-
sted in the revolution range for network syn-
chronization or load distribution.

Power generation
governor with adju-
stable speed and 
switchable overdrive 
speed

As for change-over switching fixed/variable 
speed the power generator, in fixed speed 
mode, can be used as the overdrive speed 
without loading, in variable mode or for
parallel switching.

Variable speed-, 
Min/Max-control

Variable speed, 

Min/Max governor

2)

Switching over between variable speed and 
Min/Max control.

Min/Max-control

Min/Max governor

1)

Idling and end revolutions for vehicle 
applications.

Содержание EMR 2





























































Отзывы: