Detroit Radiant Products CL3 Series Скачать руководство пользователя страница 21

Страница: 21 / 64

Side shield extension (P/N: SSE).

Directs infrared rays downward, away

from sidewalls and combustibles.

Elbow reflector (P/N: RE).

Used over a 90° elbow

radiant tube.

U-shaped reflector (P/N: RU).

Used over a ‘U’ shaped

radiant tube.

CL3

Series

Chart 3.5

•

Common Optional Accessories

* Reflectors cannot be rotated when used with a reflector elbow (RE), U-shaped reflector (RU), or side

shield (SSE).

** Refer to the Clearances to Combustibles Chart 2.1 on page 9 for minimum distances to combustibles

when side shield extension(s) are used.

Additional accessory options are listed in the Detroit Radiant Products Company Tube Heater

Accessory Guide or online at

www.detroitradiant.com.

Figure 3.16

•

Reflector Shield Accessories

3.0

Installation

•

Common Reflector Accessories

Reflector Assembly

Description

Part Number

Elbow Reflector*

90° bend, highly polished aluminum reflector elbow

designed to fit atop one elbow accessory fitting.

U-Reflector*

180° bend, highly polished aluminum reflector U-bend

designed to fit atop one U-bend accessory fitting.

Side Shield Extension**

Highly polished side shield extension used to direct

infrared rays downward, away from sidewalls and

combustibles.

SSE

Protective Guard

Used to prevent debris or objects from becoming

lodged between the radiant tube and reflector.

Required when mounting heaters below 8 feet.

Содержание CL3 Series

































































Результаты поиска

Содержание CL3 Series

Отзывы:

Похожие инструкции для CL3 Series

Бренды по названию

Популярные бренды

Detroit Radiant Products CL3 Series, Руководство по установке

Результаты поиска

Содержание CL3 Series

Отзывы:

Похожие инструкции для CL3 Series

Бренды по названию

Популярные бренды