DETEWE OpenCom 130 Скачать руководство пользователя страница 72

Страница: 72 / 204

Mounting the OpenCom 150 Rack InfoCom System

Technical Data

6.2

Technical Data

(only if different from the OpenCom 150)

Dimensions:

– Width: 19-inch panel with
flange
for mounting in installation
cabinet
–Height: 3U
– Depth: approx. 340 mm

Weight:

approx. 7.8 kg

Connection of 230 VAC power supply on rear side via inlet connector for non-
heating apparatus

Connection of all ports via RJ 45 jacks on front panel

Note:

The ISDN S

ports on the front panel may only be

switched in one direction (internal or external). Use of the ex-
ternal port with a crossover (Rx-Tx) patch cable in parallel to
the S

internal port (for two S

terminals on the same bus)

may severely limit the range of the S

bus.

Содержание OpenCom 130













































































































































































































Результаты поиска

Содержание OpenCom 130

Отзывы:

Похожие инструкции для OpenCom 130

Бренды по названию

Популярные бренды

DETEWE OpenCom 130, Руководство пользователя

Результаты поиска

Содержание OpenCom 130

Отзывы:

Похожие инструкции для OpenCom 130

Бренды по названию

Популярные бренды