DETEWE OpenCom 130 Скачать руководство пользователя страница 48

Страница: 48 / 204

Installation

Port Assignment, Termination, Cable Lengths

In the case of the OpenCom 100, the S

buses are terminated by software. You

make this setting in the S

port configuration in the

Configurator

on the Web

console.

You can connect up to eight terminals on every internal S

bus; up to three of the

terminals can operate without an external power supply. The length of the four-
wire cable of an internal S

bus must not exceed 150 m. The power consumption

of each internal S

bus is approx. 2 W.

Ports on Interface Cards

The S

bus is terminated at one end by the OpenCom 100.

IAE = ISDN socket (German: “ISDN Anschluß Einheit”) or an ISDN terminal.
TR = terminating resistor, the S

termination. The TR must be at the termination of the

line. This can also be done by an appropriately wired IAE.

The S

bus is terminated by the TR at the ends.

Termination on an ISDN socket

OpenCom

IAE

OpenCom

IAE

Содержание OpenCom 130













































































































































































































Результаты поиска

Содержание OpenCom 130

Отзывы:

Похожие инструкции для OpenCom 130

Бренды по названию

Популярные бренды

DETEWE OpenCom 130, Руководство пользователя

Результаты поиска

Содержание OpenCom 130

Отзывы:

Похожие инструкции для OpenCom 130

Бренды по названию

Популярные бренды