DETEWE OpenCom 130 Скачать руководство пользователя страница 182 | Manualshive

Страница: 182 / 204

background image

Frequently Asked Questions

Telephony

180

After restarting the OpenCom 100, nothing is indicated on the displays of any
connected terminals.

It takes a short while for the OpenCom 100 to start up.

After the restart, check whether the activity LED flashes at a rate of 10s / 1s. This
flash cycle indicates that the OpenCom 100 has started up correctly and is ready
for operation.

If the OpenCom 100 has not restarted properly, reset the OpenCom 100 to its ori-
ginal factory setting (refer to the chapter entitled

Resetting the System Data

starting on page 84).

18.2

Telephony

It is not possible to make external calls.

Check the connection between the NTBA and the OpenCom 100.

In the

Configurator

, check whether the external S

0

ports are configured correctly

(

PBX Configuration: S0

menu):

– Configuration of System- / Multi-terminal access OK?
– Port is connected to the NTBA?
– Faultless Cabling?
– Terminating resistors properly configured?

The OpenCom 100 is connected to an NTBA with a multi-terminal configura-
tion. Why is it not possible to establish external connections?

With the original factory setting, an additional external S

0

port is set for an NTBA in

the system configuration; this additional port will be used first to seize a trunk line.

Deactivate the corresponding S

0

port in the

Configurator

(

PBX Configuration:

S0

menu).

«
...
180
181
182
183
184
...
»

Содержание OpenCom 130













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OpenCom 130

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 36

SAPM71 - MINI HES W/CD PLAYER

Бренд: Panasonic Страницы: 12

Бренд: Ascon tecnologic Страницы: 4

Бренд: American Audio Lab Страницы: 31

Studio 500 Series

Бренд: JAMO Страницы: 16

Бренд: Grundig Страницы: 34

RealPresence Utility Cart 500

Бренд: Polycom Страницы: 10

Multilin DGT Series

Бренд: GE Страницы: 60

DuroZone SMZ-AC

Бренд: Duro Dyne Страницы: 12

Automower Connec

Бренд: Husqvarna Страницы: 80

Бренд: JVC Страницы: 32

Бренд: JVC Страницы: 48

Бренд: JVC Страницы: 34

Бренд: JVC Страницы: 81

Бренд: JVC Страницы: 90

CD Portable System RC-EX36S

Бренд: JVC Страницы: 2

Бренд: Kenwood Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды