DETEWE OpenCom 130 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 204

background image

Mounting the OpenCom 150 Rack InfoCom System

Safety Precautions

69

6.

Mounting the OpenCom 150 Rack
InfoCom System

The OpenCom 150 is also available as rack version for mounting in a standard
19" EIA rackmount cabinet.

OpenCom 150 Rack Frame and Ports

6.1

Safety Precautions

The system needs to be mounted in earthed cabinets or cases. Lines and cables
connected to the communications system must only be laid inside buildings.

Use a shielded Ethernet cable (STP cable, Shielded Twisted Pair cable) to connect
the OpenCom 150 to a Local Area Network (LAN).

The ambient temperature of the OpenCom 150 Rack infocom system should not
exceed 55°C. If the device is installed together with other active components, it
may be necessary to mount additional ventilation fans in the installation cabinet.

Patch cables have to be connected before connecting the system to the power
supply. Installation of the system, and in particular connection to the power
supply and protective earthing, should only be performed by skilled, qualified per-
sonnel. EN, IEC regulations, along with other recognised technical rules regarding
safety, must be observed.

Please note:

Before opening the device, pull out the plug.

DSL

«
...
69
70
71
72
73
...
»

Содержание OpenCom 130













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OpenCom 130

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 16

Бренд: MAJORITY Страницы: 32

Бренд: Polk Audio Страницы: 8

RealPresence Digital Brkout

Бренд: Polycom Страницы: 2

Бренд: Teac Страницы: 38

Бренд: Verizon Страницы: 69

Бренд: Sena Страницы: 16

Бренд: Zenith Страницы: 20

Бренд: Laser Страницы: 1

MiVoice Business 3300 ICP

Бренд: Mitel Страницы: 366

niagara4 MultiSITE Edge 10

Бренд: LG Страницы: 73

Бренд: GE Страницы: 40

Бренд: LG Страницы: 20

Бренд: LG Страницы: 24

Бренд: LG Страницы: 47

Бренд: LG Страницы: 8

Бренд: LG Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды