DETEWE OpenCom 130 Скачать руководство пользователя страница 181

Страница: 181 / 204

Frequently Asked Questions

General/Hardware

179

Position of LEDs on the OpenCom 150

With the OpenCom 150 Rack, the LEDs for LAN0 and LAN1 are placed on the front
panel.

18.1

General/Hardware

The OpenCom 100 is not functioning.

Check whether the plug-in power supply is properly connected (OpenCom 130). If
an add-on module is installed: Make sure the mains plug is properly connected.

Plug another device into the mains socket to check whether there is any voltage.

The mains plug is connected, the mains socket is supplying output, but the
OpenCom 100 still does not function.

DANGER!

This device contains hazardous voltages. To make the sys-
tem dead, remove the power plug and the plug-in power
supply from the socket.

Take the housing cover off. Is the “Power Fine” LED illuminated?

If not, contact your service centre or an authorised dealer. The AC adapter plug of
the OpenCom 100 may be defective.

AC adapter

Power Good LED

Activity LED

LAN LEDs (Ethernet-Switch)

LAN LEDs

Содержание OpenCom 130













































































































































































































Результаты поиска

Содержание OpenCom 130

Отзывы:

Похожие инструкции для OpenCom 130

Бренды по названию

Популярные бренды

DETEWE OpenCom 130, Руководство пользователя

Результаты поиска

Содержание OpenCom 130

Отзывы:

Похожие инструкции для OpenCom 130

Бренды по названию

Популярные бренды