DETEWE OpenCom 130 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 204

background image

Installation

Declarations of Conformity

24

Use a shielded Ethernet cable (STP cable, Shielded Twisted Pair cable) to connect
the OpenCom 100 to a Local Area Network (LAN).

Do not allow any fluid to penetrate the OpenCom 100, because this may cause
electric shocks or short circuits.

Do not install the OpenCom 100 during a storm. Do not connect or disconnect
lines during a storm.

The OpenCom 100 is designed for indoor use only. Lay the cables so that they
cannot be walked on or tripped over.

The connection of external devices to the sensor/actor should be performed by a
qualified electrician.

3.3

Declarations of Conformity

The OpenCom 130, OpenCom 131 and OpenCom 150 ITC systems conform to the
requirements set down in the EU directive 99/5/EC.
The Declaration of Conformity can be viewed at the DeTeWe Web site at
http://www.aastra-detewe.de.

3.4

Mounting Location

The ambient temperature for operating the OpenCom 100 must be b5
and +40°C. The power supply must be 230 V/50 Hz AC. A separate fuse for the
power supply is recommended.

To maintain the prescribed ambient temperature, mount the OpenCom 100 in a
well-ventilated location, away from direct sources of heat.

Do not position the OpenCom 100

■

in front of or above heat sources such as radiators,

■

in direct sunlight,

■

behind curtains,

■

in small, unventilated, damp rooms,

«
...
24
25
26
27
28
...
»

Содержание OpenCom 130













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OpenCom 130

Бренд: Cyrus Страницы: 6

Бренд: Velux Страницы: 11

Бренд: TANDBERG Страницы: 65

Бренд: Discount Car Stereo Страницы: 4

Бренд: Fender Страницы: 51

Бренд: Rath Страницы: 7

Бренд: ICON Страницы: 6

Бренд: M&S Systems Страницы: 12

Бренд: Polycom Страницы: 25

Бренд: Panasonic Страницы: 20

E84DGFCp Series

Бренд: Lenze Страницы: 100

Бренд: Overmax Страницы: 32

Бренд: Sharp Страницы: 32

Бренд: Sharp Страницы: 38

Бренд: Sharp Страницы: 54

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды