Deprag 428001 A Скачать руководство пользователя страница 73

Страница: 73 / 89

14.1.3 Main Controller
Number Meaning

Troubleshooting

201 Fieldbus

not

available!

Check that the fieldbus module is installed and
mounted tightly. If the fieldbus module no longer
needs to be used, deactivate the fieldbus in the
settings.

202

Software versions of power unit and main
unit are not compatible!

Please contact the DEPRAG Service Department.

203

Screwdriver and controller are not
compatible.

Ensure that you have fitted an installation
screwdriver to the AST6.

204

Lost settings, default values will be loaded. Check the settings and adjust them if necessary.

205

Error in the data storage

206

Error in the communication with power unit

Please contact DEPRAG Service.

207 not

used

208

No connection to fieldbus!

Switch off the AST6 and then switch it on again. If
the fault remains, please contact the DEPRAG
Service Department.

209

SSC driver could not be loaded!

Switch off the AST6 and then switch it on again.

Table 19:

System errors regarding the main controller

14.1.4 Communication
Number Meaning

Troubleshooting

301 No

connection

302 General

fault

303 Checksum

error

304

Module not found

305 Unknown

command

306 Timeout

Switch off the AST6 and then switch it on again. If
the fault remains, please contact the DEPRAG
Service Department.

Table 20:

System errors regarding the communication

Содержание 428001 A


























































































Результаты поиска

Содержание 428001 A

Отзывы:

Похожие инструкции для 428001 A

Бренды по названию

Популярные бренды

Deprag 428001 A, Руководство по эксплуатации

Результаты поиска

Содержание 428001 A

Отзывы:

Похожие инструкции для 428001 A

Бренды по названию

Популярные бренды