Deprag 428001 A Скачать руководство пользователя страница 72

Страница: 72 / 89

Error Display and Troubleshooting

14.1 System

Errors

If you detect that the sequence controller AST6 is defective, then send it to DEPRAG.
Under no circumstances should you try to find or remedy an electrical fault.

14.1.1 Screwdriver
Number Meaning

Troubleshooting

Screwdriver not found

Insert a screw before you switch the AST6 on.

001 Temperature

too

high

Check the screw process and adapt if required. If
necessary please contact DEPRAG Service.

002 Temperature

sensor

defect

003

Checksum error 1 in EEPROM (repairable
via the main controller)

004

EEPROM not writable (not repairable)

005

Checksum error 2 in EEPROM (not
repairable)

006

Checksum error in RAM

007

Checksum error in FLASH

008

EEPROM error: Maximum amount of
screwing cycles reached

Troubleshooting not possible

Table 17:

System errors regarding the screwdriver

14.1.2 Power Unit
Number Meaning

Troubleshooting

Power unit not found

Switch off the AST6 and then switch it on again. If
the fault remains, please contact the DEPRAG
Service Department.

101

Position indicator index signal not found

102

QEP position indicator signal missing or
wrong

103

Initialization error, spindle free?

Please ensure that the
drive of the EC screwdriver
can be turned freely. Restart the AST6.

104

Loading error of capacitor, power unit
damaged.

105

External watchdog or over current fault in
power unit

Please contact DEPRAG Service.

106 Temperature

too

high

Check the fitting process and adjust it if necessary.
If required, consult the DEPRAG Service
Department.

107 range

error

108 low

voltage

117

RAM error or set-up information / adjusting
values in flash not readable.

118

5V supply error

119

3.3V supply error

121

Supply voltage error

122

Driver supply nominal 14 Volt error

127

The directory of the flash file system could
not be read

128

A system file could not be found in the
Flash file system

132

Trial to write onto the write-protected Flash
area

133

The external 24 Volt supply is in overload

134

The 8V supply for the internal as well as
the screwdriver logic is faulty.

135

Power amplifier of the motor control is
defective.

Please contact DEPRAG Service.

Table 18:

System errors regarding the power unit

Содержание 428001 A


























































































Результаты поиска

Содержание 428001 A

Отзывы:

Похожие инструкции для 428001 A

Бренды по названию

Популярные бренды

Deprag 428001 A, Руководство по эксплуатации

Результаты поиска

Содержание 428001 A

Отзывы:

Похожие инструкции для 428001 A

Бренды по названию

Популярные бренды