9
ENGLISH
8 OPERATION
(1) Playback
PHONES
FUNCTION
VOLUME
SOURCE DIRECT
MODE
™
ON / STANDBY
¡
OFF
INTEGRATED AMPLIFIER PMA-201SA
3
4
2,6
8
1
2
3
PROG /
DIRECT
SYSTEM
POWER
OFF
ON
3
PTY
STOP
PLAY
VOLUME
/SELECT
SLEEP
MODE
TAPE
FUNCTION
PRESET
+
-
TUNER
CD
MD
4
6
4
Either turn the FUNCTION dial on the main unit
or press the remote control unit’s FUNCTION
button to select the function source to be
played.
• The function switches in the order shown
below.
✻
The function switches in the opposite order
when the dial is turned counterclockwise (
.
).
CD
MD
TAPE
AUX-2
PHONO
TUNER
DVD/AUX
FUNCTION
FUNCTION
(Main unit)
(remote control unit)
5
Start playback of the selected function source.
• For instructions on operation, refer to the
component’s operating instructions.
6
Adjust the volume.
7
Adjust the BALANCE, BASS, and TREBLE
controls and set the LOUDNESS position to the
desired position.
✻
For instructions on adjusting, see “(2) Setting
the various modes” on page 9, 10.
8
To use the source direct function:
Set the SOURCE DIRECT button to the “ON”
position.
VOLUME
VOLUME
/SELECT
(Main unit)
(remote control unit)
SOURCE DIRECT
(Main unit)
1
Check that all connections are correct.
2
Turn the volume control
fully counterclockwise
(
.
) to set the volume to
the minimum.
(Main unit)
VOLUME
3
Turn on the power.
• The indicator first flashes red, then turns
green and stops flashing (remaining lit).
(Main unit)
™
ON / STANDBY
¡
OFF
SYSTEM
POWER
ON
(remote control unit)
2
Power on/standby mode and function
memory
B
When the remote control unit is used to
turn the PMA-201SA’s power on from the
standby mode, the function is set to the
function that was selected when the
power was last set to the standby mode.
(Last memory function)
B
If the function has been cleared from the
memory, the function is set to “CD” when
the PMA-201SA’s power is turned on.
(2) Setting the various modes
[1] Adjusting the bass and treble
PHONES
FUNCTION
VOLUME
SOURCE DIRECT
MODE
™
ON / STANDBY
¡
OFF
INTEGRATED AMPLIFIER PMA-201SA
2
1
STOP
PLAY
VOLUME
/SELECT
SLEEP
MODE
TAPE
FUNCTION
PRESET
+
-
1
2
1
2
Press the MODE button to display the mode to
be adjusted (“BASS” or “TREBLE”).
Either turn the FUNCTION dial on the main unit
or use the remote control unit’s SELECT
buttons.
BASS
Playback
function source
SPEAKER
BALANCE
TREBLE
LOUDNESS
SPEAKER
Playback function source
MODE
(Main unit)
MODE
(remote control unit)
FUNCTION
VOLUME
/SELECT
(Main unit)
(remote control unit)
• To increase the bass or treble:
Turn the dial clockwise (
,
) or press the
D
button.
To decrease the bass or treble:
Turn the dial counterclockwise (
.
) or press
the
H
button.
• The bass and treble can be adjusted within
the range of –12 to 0 to +12 in steps of 2.
The response is flat at 0.
• The mode switches as follows each time the
button is pressed:
✻
When the source direct mode is on, the mode
switches as shown below (the BASS and
TREBLE adjustment modes cannot be
selected).
[2] Setting the loudness mode
PHONES
FUNCTION
VOLUME
SOURCE DIRECT
MODE
™
ON / STANDBY
¡
OFF
INTEGRATED AMPLIFIER PMA-201SA
2
1
STOP
PLAY
VOLUME
/SELECT
SLEEP
MODE
TAPE
FUNCTION
PRESET
+
-
1
2
1
2
Press the MODE button to display
“LOUDNESS”.
Either turn the FUNCTION dial on the main unit
or use the remote control unit’s SELECT
buttons.
MODE
(Main unit)
MODE
(remote control unit)
FUNCTION
VOLUME
/SELECT
(Main unit)
(remote control unit)
• To set to “ON”:
Turn the dial clockwise (
,
) or press the
D
button.
To set to “OFF”:
Turn the dial counterclockwise (
.
) or press
the
H
button.
• The mode switches as shown at the left each
time the button is pressed.
✻
“LOUDNESS” cannot be selected when the
source direct mode is on.
(decrease)
(increase)
(decrease)
(increase)
(OFF)
(ON)
(ON)
(OFF)
NOTE:
The maximum total volume increase for the bass,
treble and loudness together is +12. If for example
the bass and treble are set to +12, the sound does
not change when the loudness function is turned on
and off.
