Delta Tau ACC-72EX Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 146

background image

ACC-72EX User Manual

Diagnostics

107

DeviceNet

– Master – OPT20

The following table describes the meaning of the LEDs for the comX communication modules when the
firmware of the DeviceNet Master protocol is loaded to the comX communication module:

MNS LED (COM0)

Color

State

Meaning

Green

On

Device is online and has established one or more
connections

Green

Flashing

Device is online and has established no connection

Green/Red

Green/Red/Off

Self-test after power on:
Green on for 0,25 s, then red on for 0,25 s, then off

Red

Flashing

Connection timeout

Red

On

Critical connection failure; device has detected a network error: duplicate MAC-
ID or severe error in CAN network (CAN-bus off)

Red

Off

After start of the device and during duplicate MAC-ID check

DeviceNet

– Slave – OPT21

The following table describes the meaning of the LEDs for the comX communication modules when the
firmware of the DeviceNet Slave protocol is loaded to the comX communication module:

MNS LED (COM0)

Color

State

Meaning

Green

On

Device is online and has established one or more
connections

Green

Flashing

Device is online and has established no connection

Green/Red

Green/Red/Off

Self-test after power on:
Green on for 0,25 s, then red on for 0,25 s, then off

Red

Flashing

Connection timeout

Red

On

Critical connection failure; device has detected a network error: duplicate MAC-
ID or severe error in CAN network (CAN-bus off)

Red

Off

After start of the device and during duplicate MAC-ID check

CANopen

– Master – OPT30

The following table describes the meaning of the LEDs for the comX CANopen Master communication
modules (COMX-CA-CO/ COMX-CNCOM) when the firmware of the CANopen Master protocol is
loaded to the comX communication module:

CAN LED (COM0)

Color

State

Meaning

Green

Off

The device is executing a reset

Green

Single Flash

STOPPED: The Device is in STOPPED state

Green

Blinking

PREOPERATIONAL: The Device is in the PREOPERATIONAL state
The indicator turns on and off with a frequency of 2,5 Hz: on for 200 ms,
followed by off for 200 ms.

Green

On

OPERATIONAL: The Device is in the OPERATIONAL state

Red

Single flash

Warning Limit reached: At least one of the error counters of the CAN controller
has reached or exceeded the warning level (too many error frames).
The indicator shows one short flash (200 ms) followed by a long off phase
(1,000 ms).

Red

Double flash

Error Control Event: A guard event (NMT Slave or NMTmaster) or a heartbeat
event (Heartbeat consumer) has occurred.
The indicator shows a sequence of two short flashes (each 200 ms), separated
by a short off phase (200 ms). The sequence is finished by a long off phase
(1,000 ms).

Red

On

Bus Off: The CAN controller is bus off

«
...
105
106
107
108
109
...
»

Содержание ACC-72EX



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACC-72EX

S5120V3-EI Series

Бренд: H3C Страницы: 54

Бренд: H3C Страницы: 116

Бренд: BSS Audio Страницы: 20

Бренд: Aztech Страницы: 2

Бренд: Lancom Страницы: 25

EtherLink 3C905C-TX

Бренд: 3Com Страницы: 96

Бренд: Intercoax Страницы: 2

Бренд: Top Страницы: 21

Бренд: Handicare Страницы: 60

Бренд: Zalip Страницы: 76

Бренд: Planet Страницы: 2

JetStream T2600G-28TS

Бренд: TP-Link Страницы: 1136

Бренд: Acces Страницы: 21

Бренд: Hame Страницы: 37

Бренд: Idis Страницы: 28

Бренд: ASTRO Страницы: 12

Бренд: EtherWAN Страницы: 2

Бренд: Edimax Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды