Delta Tau ACC-72EX Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 146

background image

ACC-72EX User Manual

Software setup

77

Click Device Assignment under the Driver folder in the Navigation Area. Assign the netX Driver to the
detected COMX module by checking the checkmark box next to the detected device, and click Apply.

Note

When used with Turbo PMAC, the reset line is released too fast for
some Hilscher COMX modules, which puts them in a boot mode.
This can prevent the device from being detected by Sycon.NET
software. Make sure the device receives a system-wide reset using the
PMAC suggested M-Variables ulSystemCommandCOS and
HSF_RESET registers as shown here.

SCtrl_ulSystemCommandCOS=$55AA55AA

HCSC_HSF_RESET=1

Note that ACC-72EX Setup Assistant software automatically resets
the cards if it cannot detect the identification cookie.

The rest of the steps are protocol/module dependent, and it is strongly recommended to follow the
directions for these modules in Hilscher documentation available through their website. The current
example will be continued with specifics to EtherNet/IP Scanner/Adapter setup.

«
...
75
76
77
78
79
...
»

Содержание ACC-72EX



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACC-72EX

Бренд: D-Linke Страницы: 32

Бренд: Wattle Страницы: 6

Бренд: Baicells Страницы: 8

VigorIPPBX 2820 Series

Бренд: Draytek Страницы: 29

Бренд: UHP Страницы: 15

Бренд: Ubiquiti Страницы: 21

Бренд: Nilox Страницы: 66

Бренд: Microtek Страницы: 25

Бренд: SMC Networks Страницы: 56

SecPath F50X0 Series

Бренд: H3C Страницы: 41

GigaSpire BLAST u6

Бренд: Calix Страницы: 9

Cradlepoint AER1600

Бренд: Choose 2 rent Страницы: 5

Бренд: Cisco Страницы: 22

Бренд: Tripp Lite Страницы: 2

Бренд: Cambium Networks Страницы: 39

Бренд: Cisco Страницы: 14

Aironet 1430 Series

Бренд: Cisco Страницы: 48

Aironet 1250 Series

Бренд: Cisco Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды