Delta Tau ACC-72EX Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 146

background image

ACC-72EX User Manual

Diagnostics

108

CANopen

– Slave – OPT31

The following table describes the meaning of the LEDs for the comX CANopen Slave communication
modules (COMX-CA-CO/ COMX-CNCOS) when the firmware of the CANopen Slave protocol is loaded
to the comX communication module:

CAN LED (COM0)

Color

State

Meaning

Green

Off

The device is executing a reset

Green

Single Flash

STOPPED: The Device is in STOPPED state

Green

Blinking

PREOPERATIONAL: The Device is in the PREOPERATIONAL state
The indicator turns on and off with a frequency of 2,5 Hz: on for 200 ms,
followed by off for 200 ms.

Green

On

OPERATIONAL: The Device is in the OPERATIONAL state

Red

Off

No Error: The Device is in working condition

Red

Single flash

Warning Limit reached: At least one of the error counters of the CAN controller
has reached or exceeded the warning level (too many error frames).
The indicator shows one short flash (200 ms) followed by a long off phase
(1,000 ms).

Red

Double flash

Error Control Event: A guard event (NMT Slave or NMTmaster) or a heartbeat
event (Heartbeat consumer) has occurred.
The indicator shows a sequence of two short flashes (each 200 ms), separated
by a short off phase (200 ms). The sequence is finished by a long off phase
(1,000 ms).

Red

On

Bus Off: The CAN controller is bus off

CC-Link

– Slave – OPT51

The following table describes the meaning of the LEDs for the comX CCLink Slave communication
modules (COMX 100CA-CCS/ COMX 100CNCCS) when the firmware of the CC-Link Slave protocol is
loaded to the comX communication module:

RUN/ERR LED (COM0)

Color

State

Meaning

Green

Off

1. Before participating in the network
2. Unable to detect carrier
3. Timeout
4. Resetting hardware

Green

On

Receive both refresh and polling signals or just the refresh signal normally, after
participating in the network.

Red

Off

1. Normal communication
2. Resetting hardware

Red

Blinking

The switch setting has been changed from the setting at the reset cancellation
(blinks for 0.4 sec.).

Red

On

1. CRC error
2. Address parameter error (0, 65 or greater is set including the number of
occupied stations)
3. Baud rate switch setting error during cancellation of reset (5 or greater)

«
...
106
107
108
109
110
...
»

Содержание ACC-72EX



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACC-72EX

Бренд: Sagem Страницы: 19

Бренд: JCG Страницы: 2

Бренд: Juniper Страницы: 502

PoleVault System A/V Source Inputs

Бренд: Extron electronics Страницы: 4

Net2Air Ins-40085-US

Бренд: Paxton Страницы: 4

Бренд: ZyXEL Communications Страницы: 215

Hotwire ATM Line Cards 8335

Бренд: Paradyne Страницы: 132

TE100-S16 - 10/100Mbps Ethernet Switch

Бренд: TRENDnet Страницы: 15

Бренд: Cisco MERAKI Страницы: 4

Бренд: Techroutes Страницы: 20

Бренд: Solwise Страницы: 231

Бренд: Steren Страницы: 130

Бренд: Sharedband Страницы: 3

Redbooks Emulex VFA5

Бренд: IBM Страницы: 15

Barricade SMC7908VoWBRA2

Бренд: SMC Networks Страницы: 2

Бренд: ICP DAS USA Страницы: 60

Бренд: LOBENN Страницы: 86

Бренд: Westermo Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды