Delta Tau ACC-72EX Скачать руководство пользователя страница 113

Страница: 113 / 146

ACC-72EX User Manual

Diagnostics

113

Open Modbus/TCP

– OPT80

The following table describes the meaning of the LEDs for the comX Real-Time Ethernet communication
modules (COMX 100CA-RE/ COMX 100CN-RE) when the firmware of the Open Modbus/TCP protocol
is loaded to the comX communication module:

RUN LED (COM0)

Color

State

Meaning

Green

Off

Not Ready
OMB task is not ready

Green

Flashing cyclic with 1Hz

Ready, not configured yet
OMB task is ready and not configured yet

Green

Flashing cyclic with 5Hz

Waiting for Communication:
OMB task is configured

Green

Connected:
OMB task has communication – at least one TCP connection is established

ERR LED (COM1)

Color

State

Meaning

Red

Off

No communication error

Red

Flashing cyclic with 2Hz

(On/Off ratio 25%)

System error

Red/Green

Communication error active

LINK LED

Green LED on ETH0 / ETH1 connectors:

Color

State

Meaning

Green

A connection to the Ethernet exists

Green

Off

The device has no connection to the Ethernet

ACT LED

Yellow LED on ETH0 / ETH1 connectors:

Color

State

Meaning

Yellow

Flashing

The device sends/receives Ethernet frames

Содержание ACC-72EX



















































































































































Результаты поиска

Содержание ACC-72EX

Отзывы:

Похожие инструкции для ACC-72EX

Бренды по названию

Популярные бренды

Delta Tau ACC-72EX, Справочник по аппаратуре

Результаты поиска

Содержание ACC-72EX

Отзывы:

Похожие инструкции для ACC-72EX

Бренды по названию

Популярные бренды