seq
sequence-number
{deny |permit}
ip-prefix
[ge min-prefix-length] [le max-
prefix-length]
The optional parameters are:
–
ge min-prefix-length
: is the minimum prefix length to match (from 0 to 32).
–
le max-prefix-length
: is the maximum prefix length to match (from 0 to 32).
For configuration information about prefix lists, refer to
Applying Prefix Lists
To apply prefix lists to incoming or outgoing OSPF routes, use the following commands.
• Apply a configured prefix list to incoming OSPF routes.
CONFIG-ROUTEROSPF-id mode
distribute-list
prefix-list-name
in [
interface
]
• Assign a configured prefix list to outgoing OSPF routes.
CONFIG-ROUTEROSPF-id
distribute-list
prefix-list-name
out [connected | isis | rip | static]
Redistributing Routes
You can add routes from other routing instances or protocols to the OSPF process.
With the
redistribute
command, you can include RIP, static, or directly connected routes in the OSPF
process.
NOTE: Do not route iBGP routes to OSPF unless there are route-maps associated with the OSPF
redistribution.
To redistribute routes, use the following command.
• Specify which routes are redistributed into OSPF process.
CONFIG-ROUTEROSPF-id mode
redistribute {bgp | connected | isis | rip | static} [metric
metric-value
|
metric-type
type-value
] [route-map
map-name
] [tag
tag-value
]
Configure the following required and optional parameters:
–
bgp, connected, isis, rip, static
: enter one of the keywords to redistribute those
routes.
–
metric
metric-value
: the range is from 0 to 4294967295.
–
metric-type
metric-type
: 1 for OSPF external route type 1. 2 for OSPF external route type 2.
–
route-map
map-name
: enter a name of a configured route map.
–
tag
tag-value
: the range is from 0 to 4294967295.
Example of Viewing OSPF Configuration after Redistributing Routes
To view the current OSPF configuration, use the
show running-config ospf
command in EXEC
mode or the
show config
command in ROUTER OSPF mode.
Dell(conf-router_ospf)#show config
!
708
Open Shortest Path First (OSPFv2 and OSPFv3)
Содержание S4820T
