Dell PowerEdge T110 Скачать руководство пользователя страница 41

Страница: 41 / 144

Using the System Setup Program and UEFI Boot Manager

Boot Settings Screen

Port A
(

Off

default)

Auto

enables BIOS support for the device attached to

SATA port A.

Off

disables BIOS support for the device.

Port B
(

Off

default)

Auto

enables BIOS support for the device attached to

SATA port B.

Off

disables BIOS support for the device.

Port C
(

Off

default)

Auto

enables BIOS support for the device attached to

SATA port C.

Off

disables BIOS support for the device.

Port D
(

Off

default)

Auto

enables BIOS support for the device attached to

SATA port D.

Off

disables BIOS support for the device.

Port E
(

Off

default)

Auto

enables BIOS support for the device attached to

SATA port E.

Off

disables BIOS support for the device.

eSATA Port
(

Off

default)

Auto

enables BIOS support for the device attached to the

eSATA port.

Off

disables BIOS support for the device.

Option

Description

Boot Mode
(

BIOS

default)

CAUTION:

Switching the boot mode could prevent

the system from booting if the operating system was
not installed in the same boot mode.

If the operating system supports Unified Extensible
Firmware Interface, you can set this option to

UEFI

Setting this field to

BIOS

allows compatibility with non-

UEFI operating systems.

NOTE:

Setting this field to

UEFI

disables the

Boot

Sequence

Hard-Disk Drive Sequence

, and

USB Flash Drive

Emulation Type

fields.

Boot Sequence

Boot Mode

is set to

BIOS

, this field tells the system

where the operating system files needed for startup are
located. If

Boot Mode

is set to

UEFI

, you can access the

UEFI boot manager utility by rebooting the system and
pressing <F11> when prompted to do so.

Hard-Disk Drive
Sequence

Determines the order in which the BIOS will attempt to
boot from hard drives in the system during system
startup.

Option

Description

Mayzie_HOM.book Page 41 Monday, August 31, 2009 9:33 PM

Содержание PowerEdge T110

















































































































































Результаты поиска

Содержание PowerEdge T110

Отзывы:

Похожие инструкции для PowerEdge T110

Бренды по названию

Популярные бренды

Dell PowerEdge T110, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge T110

Отзывы:

Похожие инструкции для PowerEdge T110

Бренды по названию

Популярные бренды