Dell PowerConnect B-FCX Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 86

background image

PowerConnect B-FCX Switch Hardware Installation Guide

47

53-1002267-01

Troubleshooting network connections

3

The output from this command appears below.

Syntax: show cable-diag tdr <

port-num

>

Table 20

defines the fields shown in this output.

Digital optical monitoring

You can configure your device to monitor optical transceivers in the system, either globally or by
specified port. When this feature is enabled, the system monitors the temperature and signal
power levels for the optical transceivers in the specified ports. Console messages and syslog
messages are sent when optical operating conditions fall below or rise above the XFP, SFP, and
SFP+ manufacturer’s recommended thresholds. For more information about digital optical
monitoring, refer to

PowerConnect B-FCX Series Configuration Guide

.

TABLE 20

Cable statistics

This Line...

Displays...

Port

The port that was tested.

Speed

The current line speed of the port.

Local pair

The local link name.

Pair Length

The cable length when terminated, or the distance to the point of fault when the line
is not up.

Remote pair

The remote link name.

Pair status

The status of the link. This field displays one of the following:

•

Terminated: The link is up.

•

Shorted: A short is detected in the cable.

•

Open: An opening is detected in the cable.

•

ImpedMis: The impedance is mismatched.

•

Failed: The TDR test failed.

PowerConnect# show cable-diag tdr 1/1/1

Port Speed Local pair Pair Length Remote pair Pair status

--------- ----- ---------- ----------- ----------- -----------

1/1/1 1000M Pair A <50M Pair B Terminated

Pair B <50M Pair A Terminated

Pair C <50M Pair D Terminated

Pair D <50M Pair C Terminated

«
...
55
56
57
58
59
...
»

Содержание PowerConnect B-FCX























































































Отзывы:

Нет отзывов

Похожие инструкции для PowerConnect B-FCX

Бренд: Dataprobe Страницы: 31

Бренд: IBM Страницы: 13

Flex System EN2092

Бренд: IBM Страницы: 2

Бренд: BABBITT Страницы: 14

Бренд: BABBITT Страницы: 10

Бренд: Lindy Страницы: 70

Бренд: Eaton Страницы: 2

Бренд: Conceptronic Страницы: 7

Бренд: Flamingo Страницы: 2

Ethernet Switch Boards

Бренд: Intel Страницы: 52

Бренд: Tripp Lite Страницы: 3

SBX 95 SE - AV Control 4

Бренд: Vivanco Страницы: 16

SMT-8-...-B Series

Бренд: Festo Страницы: 2

Бренд: APG Страницы: 7

Бренд: Hamlet Страницы: 2

Бренд: Rose electronics Страницы: 2

Бренд: Ascent Communication Technology Страницы: 8

kontron KSwitch D1 UGP

Бренд: S&T Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды