Dell PowerConnect B-FCX Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 86

background image

PowerConnect B-FCX Switch Hardware Installation Guide

7

53-1002267-01

Hardware features

1

CAUTION

The optional 10Gbps XFP module is not hot-swappable.

FIGURE 7

Two-port 10 Gbps XFP module

Optional Four-port 1 Gbps SFP and 10 Gbps SFP+ modules

The PowerConnect B-FCX624 and PowerConnect B-FCX648 devices include a slot on the front
panel for a four-port 1 Gbps SFP module, or a four-port 10 Gbps SFP+ module. The 1 Gbps SFP
module operates at 1 Gbps full duplex, and the 10 Gbps SFP+ module operates at 10 Gbps full
duplex.

PowerConnect B-FCX624 and PowerConnect B-FCX648 devices can be used in an IronStack by
installing the optional 10 Gbps SFP+ module, and connecting devices using standard duplex LC
cables. These devices cannot be combined in a stack with non-PowerConnect B-FCX devices. For
detailed information about how to configure PowerConnect B-FCX devices in an IronStack topology,
see the

PowerConnect B-FCX Series Configuration Guide

.

NOTE

The 1 Gbps SFP and 10 Gbps SFP+ modules are not hot-swappable.

FIGURE 8

Four-port 1 Gbps SFP module

TABLE 4

10 Gbps XFP module port status LEDs

LED

Condition

Status

Link or Act LED (Link or
Activity)

On or flashing Green

Port has a valid link at 10 Gbps. Flashing indicates activity.

Off

The link is down.

TABLE 5

Four-port 1 Gbps SFP module status LEDs

LED

Condition

Status

Link or Act LED (Link or
Activity)

On or flashing Green

Port has a valid link at 1 Gbps. Flashing indicates activity.

Off

The link is down.

FCX-4G

1F 2F 3F 4F

«
...
15
16
17
18
19
...
»

Содержание PowerConnect B-FCX























































































Отзывы:

Нет отзывов

Похожие инструкции для PowerConnect B-FCX

Бренд: 4O3A Страницы: 2

Бренд: SMART Страницы: 46

MatrixPRO 8x8 DVI

Бренд: Barco Страницы: 2

ET2-0602-M Series

Бренд: Leonton Страницы: 17

Бренд: Festo Страницы: 2

Бренд: A-Neuvideo Страницы: 28

TradeSwitch2-USB

Бренд: G&D Страницы: 88

Бренд: Electroswitch Страницы: 6

Бренд: Linkskey Страницы: 2

Бренд: Planet Страницы: 2

Бренд: Comprehensive Страницы: 12

R-TEC Automation RTMWSR15C

Бренд: Rowley Страницы: 10

Cordex HP CXRF 48-2.4kW

Бренд: Alpha Страницы: 56

JTECH-4K88-EX-RX

Бренд: J-TECH Страницы: 40

Бренд: National Instruments Страницы: 23

Бренд: SEH Страницы: 40

Бренд: CTC Union Страницы: 14

CUVEO CR-UPS2000

Бренд: Me Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды