Dell PowerConnect B-FCX Скачать руководство пользователя страница 22

Страница: 22 / 86

PowerConnect B-FCX Switch Hardware Installation Guide

53-1002267-01

Hardware features

FIGURE 14

System status LEDs

SFP
(1F~4F)
Link or
Activity

On/Flashing Green

The SFP port has established a valid 100/1000 Mbps link.
Flashing indicates the port is transmitting and receiving user
packets.

Off

A link is not established with a remote port.

SFP+
(1F~4F)
Link or
Activity

On/Flashing Green

The SFP+ port has established a valid 10 Gbps link. Flashing
indicates the port is transmitting and receiving user packets.

Off

A link is not established with a remote port.

System status LEDs

TABLE 12

System status LEDs

LED

Condition

Status

PS1
PS2
(Power Supply
Status)

Green

Power supply is operating normally. It is installed properly and the
power cord is attached to a power source.

Amber

Power supply fault. The power supply may not be installed properly.

Off

Power off or failure.

Diag
(Diagnostic)

Flashing Green

System self-diagnostic test in progress.

Green

System self-diagnostic test successfully completed.

Amber

System self-diagnostic test has detected a fault. (Blower, thermal or
any interface fault.)

Out-of-band
Management
Link or Activity

On/Flashing Green

The port has established a valid link at 10/100/1000 Mbps.
Flashing indicates the port is transmitting and receiving user
packets.

Off

A link is not established with a remote port.

TABLE 11

Port status LEDs (Continued)

LED

Condition

Status

Reset

Diag

Console

Mgmt

Содержание PowerConnect B-FCX























































































Результаты поиска

Содержание PowerConnect B-FCX

Отзывы:

Похожие инструкции для PowerConnect B-FCX

Бренды по названию

Популярные бренды

Dell PowerConnect B-FCX, Руководство по установке оборудования

Результаты поиска

Содержание PowerConnect B-FCX

Отзывы:

Похожие инструкции для PowerConnect B-FCX

Бренды по названию

Популярные бренды