Dell Inspiron 2100 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 73

background image

Removing and Replacing Parts

4-9

4. If the drive is a SCSI drive, record the setting of the SCSI address

jumpers and SCSI bus termination jumper.

5. If present, remove the 50-pin to 68-pin adapter from the SCSI connec-

tor on the back of the drive.

Some drives use a 50-pin to 68-pin adapter between the SCSI cable and the
drive connector. Check the back of the drive for an adapter, if present,
remove it and retain it for use on the new drive.

Figure 4-7. Drive-Mounting Rails and Extensions Removal

When you reinstall a SCSI drive, set the SCSI address jumpers and the SCSI
bus termination jumpers to the settings you recorded.

drive-release
tabs

drive-mounting rails (2)

drive-mounting
extensions

50- to 68-pin
adapter

«
...
58
59
60
61
62
...
»

Содержание Inspiron 2100










































































Отзывы:

Нет отзывов

Похожие инструкции для Inspiron 2100

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 43

Бренд: Everex Страницы: 47

Бренд: Advantech Страницы: 44

Бренд: Sun Microsystems Страницы: 45

Ferrari 1000 Series

Бренд: Acer Страницы: 123

Бренд: Acer Страницы: 112

Бренд: Advanced Micro Computers Страницы: 77

Бренд: Vivo Страницы: 3

SIMATIC VPU200-3104

Бренд: Siemens Страницы: 28

SIMATIC Rack PC IL 40

Бренд: Siemens Страницы: 40

SIMATIC PC BI10

Бренд: Siemens Страницы: 45

SIMATIC RI 45 PIII Series

Бренд: Siemens Страницы: 132

Бренд: Siemens Страницы: 194

SIMATIC IPC627D

Бренд: Siemens Страницы: 186

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды