Dell Inspiron 2100 Скачать руководство пользователя страница 33

Страница: 33 / 73

1-16

Dell PowerEdge 2100/180 and 2100/200 Systems Service Manual

Table 1-2. Jumper Descriptions

Jumper

Description

Settings

200MHZ

Microprocessor speed

Installed if the micro-
processor’s internal speed is
200 MHz, otherwise, not
installed.

180MHZ

Microprocessor speed

Installed if the micro-
processor’s internal speed is
180 MHz, otherwise, not
installed.

PASSWD

Password enable/disable

Jumper installed to activate
boot password feature.

EISA

Clear EISA configuration
settings

Install the jumper and boot
the system to clear the con-
figuration settings.

Remove the jumper and use
the EISA Configuration Util-
ity to configure the system.

VGA

Integrated VGA controller
enable/disable

Install to enable the inte-
grated VGA controller.

CARDBIOS

Used for trouble shooting

Install the jumper to boot
system from BIOS expan-
sion card.

Remove the jumper to allow
normal boot operation from
BIOS.

Содержание Inspiron 2100










































































Результаты поиска

Содержание Inspiron 2100

Отзывы:

Похожие инструкции для Inspiron 2100

Бренды по названию

Популярные бренды

Dell Inspiron 2100, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 2100

Отзывы:

Похожие инструкции для Inspiron 2100

Бренды по названию

Популярные бренды