Dell Inspiron 2100 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 73

background image

Beep Codes and Error Messages

3-3

S

ystem Error Messages

Table 3-2 lists (in alphabetical order) system error messages that can appear on
the monitor screen. These messages can help you find the source of a problem.
Some of these error messages indicate fatal errors. When a fatal error occurs,
the system cannot usually be rebooted until an appropriate hardware change has
been made.

Table 3-2. System Error Messages

Message

Definition

Probable Causes

System bat-
tery is dead
- Replace
and run
Setup

The system battery
is dead.

Replace the battery
and run the System
Setup program.

System CMOS
checksum
bad - Run
Setup

The configuration
data is corrupted.

Run the System Setup
program to restore your
system configuration.

Incorrect
drive A type
- Run Setup

The diskette drive
does not match the
diskette drive type
stored in the config-
uration data.

Run the System Setup
program to restore your
system configuration.

Incorrect
drive B type
- Run Setup

The diskette drive
does not match the
diskette drive type
stored in the config-
uration data.

Run the System Setup
program to restore your
system configuration.

Keyboard
error

A cable may be
loose, or the key-
board may be faulty.

Defective keyboard,
keyboard cable, or
system board.

Stuck key

A cable may be
loose, or the key-
board may be faulty.

Defective keyboard or
keyboard cable.

System/
Shadow RAM
failed at
offset:

One or more
DIMMs may be
improperly seated or
faulty.

Reseat the DIMMs or
replace the DIMMs.

«
...
46
47
48
49
50
...
»

Содержание Inspiron 2100










































































Отзывы:

Нет отзывов

Похожие инструкции для Inspiron 2100

PC 300 GL Type 6272

Бренд: IBM Страницы: 94

F50 RS/6000 7025

Бренд: IBM Страницы: 364

FPMA-MOBILE1800

Бренд: New Star Computer Products Страницы: 4

Бренд: E-Medic Страницы: 31

BRIX GB-BACE-3150

Бренд: Gigabyte Страницы: 2

Бренд: XPLORE TECHNOLOGIES Страницы: 2

Бренд: FabiaTech Страницы: 65

Бренд: HP Страницы: 53

Бренд: Honeywell Страницы: 100

PowerEdge 1600SC

Бренд: Dell Страницы: 56

Бренд: TYAN Страницы: 33

Бренд: TYAN Страницы: 101

Бренд: ClearCube Страницы: 4

Бренд: Radio Shack Страницы: 2

Бренд: Corvus systems Страницы: 191

Бренд: Shuttle Страницы: 23

ZBOX nano VDO1 PLUS

Бренд: Zotac Страницы: 30

THE LITTLE MERMAID COMPUTER

Бренд: LEXIBOOK Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды