Dell Inspiron 2100 Скачать руководство пользователя страница 67

Страница: 67 / 73

4-16

Dell PowerEdge 2100/180 and 2100/200 Systems Service Manual

Microprocessor/Heat Sink Assembly

Figure 4-15. Microprocessor Securing Clip Removal

To remove the microprocessor/heat sink assembly, follow these steps:

1. Remove the system board assembly.

2. Lay the system board assembly on a flat surface.

3. Remove the microprocessor securing clip from the microprocessor/heat

sink assembly.

Press down on the folded part of the clip with a small screwdriver to release
the clip.

4. Push outward and then upward on the release lever to rotate the lever

to its fully vertical position.

5. Lift the microprocessor/heat sink assembly out of its socket (see

Figure 4-16).

WARNING: The microprocessor can get extremely hot during sys-
tem operations. Be sure it has had sufficient time to cool before
touching it.

microprocessor
securing clip hooks
over tabs on socket
(front and back)

microprocessor

heat sink

socket release
lever

microprocessor
socket

Содержание Inspiron 2100










































































Результаты поиска

Содержание Inspiron 2100

Отзывы:

Похожие инструкции для Inspiron 2100

Бренды по названию

Популярные бренды

Dell Inspiron 2100, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 2100

Отзывы:

Похожие инструкции для Inspiron 2100

Бренды по названию

Популярные бренды