Dell Inspiron 1318 Скачать руководство пользователя страница 46

Страница: 46 / 46

18.

Lift the system board at an angle toward the side of the computer and out of the computer base.

Replacing the System Board

Follow all of the steps in

Removing the System Board

in reverse order.

Slide the battery into the battery bay, until it clicks into place.

Turn on the computer.

Insert the CD that accompanied the replacement system board into the appropriate drive. Follow the instructions that appear on the screen.

Back to Contents Page

system board

wireless switch assembly board

NOTICE:

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in

damage to the computer.

NOTE:

After you have replaced the system board, enter the computer Service Tag into the BIOS of the replacement system board.

Содержание Inspiron 1318















































Результаты поиска

Содержание Inspiron 1318

Отзывы:

Похожие инструкции для Inspiron 1318

Бренды по названию

Популярные бренды

Dell Inspiron 1318, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 1318

Отзывы:

Похожие инструкции для Inspiron 1318

Бренды по названию

Популярные бренды