Dell Inspiron 1318 Скачать руководство пользователя страница 10

Страница: 10 / 46

Back to Contents Page

Camera (Optional)

Dell™ Inspiron™ 1318 Service Manual

Removing the Camera

Replacing the Camera

Removing the Camera

Follow the instructions in

Before You Begin

Remove the display assembly (see

Display

Remove the display bezel (see

Display

Remove the display panel (see

Display

Remove the two M2 x 3-mm screws that secure the camera.

Disconnect the camera cable from the camera cable connector.

Remove the camera.

Replacing the Camera

Connect the camera cable to the camera cable connector.

Align the camera with the screw holes on the display frame.

Replace the two M2 x 3-mm screws that secure the camera to the display frame.

Replace the display panel (see

Display

Replace the display bezel (see

Display

Replace the display assembly (see

Display

Slide the battery into the battery bay, until it clicks into place.

CAUTION:

Before working inside your computer, follow the safety instructions shipped with your computer.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as a connector on the back of the computer).

camera cable connector

camera

M2 x 3-mm screws (2)

Содержание Inspiron 1318















































Результаты поиска

Содержание Inspiron 1318

Отзывы:

Похожие инструкции для Inspiron 1318

Бренды по названию

Популярные бренды

Dell Inspiron 1318, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 1318

Отзывы:

Похожие инструкции для Inspiron 1318

Бренды по названию

Популярные бренды