Dell Inspiron 1318 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 46

background image

Replacing the Hard Drive

1.

Remove the new drive from its packaging.

2.

Place the hard drive in the bracket and replace the two M2 x 3-mm screws on either side.

3.

Slide the hard drive into the bay.

4.

Replace the four M3 x 3-mm screws on the hard drive.

5.

Slide the battery into the battery bay, until it clicks into place.

6.

Install the operating system for your computer, as needed (see "Restoring Your Operating System" in your

Setup Guide

).

7.

Install the drivers and utilities for your computer, as needed (see "Reinstalling Drivers and Utilities" in your

Setup Guide

).

Back to Contents Page

NOTE:

Save the original packaging for storing or shipping the hard drive.

«
...
22
23
24
25
26
...
»

Содержание Inspiron 1318















































Отзывы:

Нет отзывов

Похожие инструкции для Inspiron 1318

Бренд: @Xi Computer Corporation Страницы: 118

Бренд: ADLINK Technology Страницы: 76

Бренд: IBM Страницы: 74

Бренд: Aaeon Страницы: 43

Бренд: Vivo Страницы: 8

Бренд: Dell Страницы: 121

Бренд: Acnodes Страницы: 2

Бренд: Sharp Страницы: 13

Shuttle PN-SPCi5W7

Бренд: Sharp Страницы: 14

Бренд: Sharp Страницы: 14

Бренд: Sharp Страницы: 58

Vaio VGN-CR515E

Бренд: Sony Страницы: 2

Бренд: Habey Страницы: 4

WINSTON WORKSTATION

Бренд: Innovative Страницы: 11

Pro-face PS-2000B-41

Бренд: Digital Electronics Corporation Страницы: 105

FORTOOLS PORTABLECLAMPING WORKSTATION

Бренд: Keter Страницы: 28

Бренд: Norsk Data Страницы: 66

Kontron SBOX-5210

Бренд: S&T Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды