Dell Inspiron 1318 Скачать руководство пользователя страница 3

Страница: 3 / 46

Back to Contents Page

Battery Latch Assembly

Dell™ Inspiron™ 1318 Service Manual

Removing the Battery Latch Assembly

Replacing the Battery Latch Assembly

Removing the Battery Latch Assembly

Remove the system board (see

System Board

Remove the charger board (see

Charger Board

Press the plastic grip together to release the latch button.

Slide the battery latch assembly to the right to remove it.

Replacing the Battery Latch Assembly

Replace the spring and slide the battery latch assembly into place.

Replace the latch button.

Replace the charger board (see

Charger Board

Replace the system board (see

System Board

Slide the battery into the battery bay, until it clicks into place.

CAUTION:

Before performing the following procedures, follow the safety instructions shipped with your computer.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching a connector on the back panel of

the computer.

NOTICE:

Before you remove the battery release button, observe the orientation of the button to ensure proper installation when the button is

replaced.

latch assembly

plastic grip

NOTICE:

Ensure the battery latch assembly is properly oriented. The indent for the button should face up when installing the assembly.

Содержание Inspiron 1318















































Результаты поиска

Содержание Inspiron 1318

Отзывы:

Похожие инструкции для Inspiron 1318

Бренды по названию

Популярные бренды

Dell Inspiron 1318, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 1318

Отзывы:

Похожие инструкции для Inspiron 1318

Бренды по названию

Популярные бренды