Dell Inspiron 1318 Скачать руководство пользователя страница 40

Страница: 40 / 46

Back to Contents Page

Power Board

Dell™ Inspiron™ 1318 Service Manual

Removing the Power Board

Replacing the Power Board

Removing the Power Board

Follow the procedures in

Before You Begin

Remove the center control cover (see

Center Control Cover

Remove the keyboard (see

Keyboard

Remove the screw that secures the power board to the system board.

Lift and turn the power board over to access the power board connector.

Push the black tab away from the connector to disconnect the power board cable.

Replacing the Power Board

Slide the power board cable into the connector.

Push the black tab towards the connector to secure the power board cable.

Align the screw hole on the power board with the screw hole on the system board and replace the screw.

Replace the keyboard (see

Keyboard

Replace the center control panel (see

Center Control Cover

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions shipped with your computer.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as a connector on the back of the computer).

NOTICE:

To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the

computer.

NOTICE:

Be extremely careful when disconnecting the cable. The cable connector is very fragile.

NOTICE:

Be extremely careful when removing and handling the power board. Failure to do so could result in scratching the display panel.

M2 x 2-mm screw

black tab

power board cable

power board

Содержание Inspiron 1318















































Результаты поиска

Содержание Inspiron 1318

Отзывы:

Похожие инструкции для Inspiron 1318

Бренды по названию

Популярные бренды

Dell Inspiron 1318, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 1318

Отзывы:

Похожие инструкции для Inspiron 1318

Бренды по названию

Популярные бренды