Dell Inspiron 1318 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 46

background image

Back to Contents Page

Display

Dell™ Inspiron™ 1318 Service Manual

Removing the Display Assembly

Replacing the Display Assembly

Removing the Display Bezel

Replacing the Display Bezel

Removing the Display Panel

Replacing the Display Panel

Removing the Display Panel Cable

Replacing the Display Panel Cable

Removing the Display Assembly

1.

Follow the instructions in "Before You Begin" on page 9.

2.

Remove the memory module(s) (see

3.

Remove the WLAN card (see

).

4.

Make note of the cable routing and carefully remove the antenna cables from their routing guides. Pull the cables with their connectors through the
system board so that they are clear of the computer base.

5.

Remove the two M2.5 x 5-mm screws from the computer base.

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions shipped with your computer.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as a connector on the back of the computer).

NOTICE:

To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the

computer.

«
...
16
17
18
19
20
...
»

Содержание Inspiron 1318















































Отзывы:

Нет отзывов

Похожие инструкции для Inspiron 1318

Бренд: Barco Страницы: 2

DECstaion 5000 240

Бренд: Digital Equipment Страницы: 62

Millenium Studio Desk WS20

Бренд: thomann Страницы: 2

Бренд: DT Research Страницы: 2

Бренд: Acer Страницы: 48

Бренд: Acer Страницы: 68

5535-5050 - Aspire

Бренд: Acer Страницы: 11

Бренд: Acer Страницы: 24

Бренд: Acer Страницы: 24

Бренд: Acer Страницы: 22

Бренд: Acer Страницы: 117

Бренд: Acer Страницы: 108

AcerPower S series

Бренд: Acer Страницы: 53

Бренд: Acer Страницы: 113

Бренд: Acer Страницы: 122

Бренд: Acer Страницы: 72

Бренд: Acer Страницы: 164

Бренд: Acer Страницы: 109

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды