Dell Inspiron 1318 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 46

background image

6.

Turn the computer over and replace the two M2.5 x 5-mm screws on the computer base.

7.

Carefully route the WLAN card antenna cables through their routing guides and connect them to the WLAN card.

8.

Reconnect the WLAN card if applicable (see

).

9.

Replace the memory module(s) (see

Removing the Display Bezel

1.

Remove the display assembly (see

).

2.

Using your fingertips, carefully pry up the inside edge of the display bezel.

3.

Remove the display bezel.

Replacing the Display Bezel

Align the display bezel over the display panel, and gently snap into place.

Removing the Display Panel

1.

Remove the display assembly (see

).

2.

Remove the display bezel (see

).

3.

Remove the six screws securing the display panel.

NOTICE:

The display bezel is extremely fragile. Be careful when removing it to prevent damaging the bezel.

NOTE:

Note how the cables have been routed to the display panel.

«
...
18
19
20
21
22
...
»

Содержание Inspiron 1318















































Отзывы:

Нет отзывов

Похожие инструкции для Inspiron 1318

Бренд: IBM Страницы: 155

Бренд: Energy Star Страницы: 17

Бренд: Texim Europe Страницы: 5

ThinkCentre 8104

Бренд: IBM Страницы: 38

Бренд: ESI Страницы: 8

ECS-9755-505MGTX950

Бренд: Vecow Страницы: 111

Бренд: Elo TouchSystems Страницы: 3

PCV-RZ14G Online Help Center (VAIO User Guide)

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 2

PCV-RXA842 Online Help Center (VAIO User Guide)

Бренд: Sony Страницы: 1

PCV-RX820 Online Help Center (primary )

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

PCV-RX770 Computer User Guide (primary manual)

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 2

PCV-RX742 Online Help Center (primary manual)

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

PCV-RX690G User

Бренд: Sony Страницы: 1

PCV-RZ-M Series VAIO

Бренд: Sony Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды