Dell Inspiron 1318 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 46

background image

Back to Contents Page

Center Control Cover

Dell™ Inspiron™ 1318 Service Manual

Removing the Center Control Cover

Replacing the Center Control Cover

Removing the Center Control Cover

1.

Follow the procedures in

Before You Begin

2.

Remove the two M2 x 3-mm screws that secure the center control cover.

3.

Turn the computer and open the display as far as possible.

4.

Pry the center control cover up, and turn it over on top of the keyboard.

5.

Lift the cable release tab and disconnect the center control cover cable.

6.

Remove the center control cover.

Replacing the Center Control Cover

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions shipped with your computer.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as a connector on the back of the computer).

NOTICE:

To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the

computer.

NOTICE:

Be extremely careful when removing the center control cover. The cable connector is very fragile.

1

cable release tab

2

center control cover cable

3

center control cover

«
...
23
24
25
26
27
...
»

Содержание Inspiron 1318















































Отзывы:

Нет отзывов

Похожие инструкции для Inspiron 1318

Бренд: IBM Страницы: 120

Desktop Hardware

Бренд: Digiop Страницы: 2

Бренд: Displays2go Страницы: 2

SST-GD02B Grandia Sereis GD02

Бренд: SilverStone Страницы: 14

WM342-KD Series

Бренд: DFI Страницы: 12

eBOX530-820-FL Series

Бренд: AXIOMTEK Страницы: 2

Бренд: Alienware Страницы: 21

Бренд: Acrosser Technology Страницы: 17

Бренд: Zotac Страницы: 20

Бренд: Fujitsu Страницы: 8

Бренд: Fujitsu Страницы: 13

ESPRIMO P910 E85+

Бренд: Fujitsu Страницы: 10

Бренд: Fujitsu Страницы: 10

Бренд: Fujitsu Страницы: 14

Бренд: Fujitsu Страницы: 43

Бренд: Fujitsu Страницы: 6

Бренд: Fujitsu Страницы: 7

Бренд: Fujitsu Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды