Dell D03T Скачать руководство пользователя страница 59

Страница: 59 / 119

About this task

The following images indicate the location of the heat-sink assembly and provide a visual representation of the removal
procedure.

Steps

1. Using a Torx T20 screwdriver, in reverse sequential order (4->3->2->1), loosen the four captive screws that secure the

heat-sink assembly to the system board.

2. Lift the heat-sink assembly from the system board.

Installing the heat-sink assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

NOTE:

If either the processor or the heat sink is replaced, use the thermal grease that is provided in the kit to ensure that

thermal conductivity is achieved.

About this task

The following images indicate the location of the heat-sink assembly and provides a visual representation of the installation
procedure.

Removing and installing components

Содержание D03T
























































































































Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды

Dell D03T, Руководство по обслуживанию

Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды