Dell D03T Скачать руководство пользователя страница 104

Страница: 104 / 119

Table 7. System setup options—Storage menu (continued)

Storage

Type

Displays the M.2 PCIe SSD type information of the system.

Device

Displays the M.2 PCIe SSD device information of the system.

Enable MediaCard

Secure Digital (SD) Card

Enable or disable the SD card.

By default, the

Secure Digital (SD) Card

option is enabled.

Secure Digital (SD) Card Read-Only Mode Enable or disable the SD card read-only mode.

By default, the

Secure Digital (SD) Card Read-Only Mode

option is not

enabled.

Table 8. System setup options—Display menu

Display

Display Brightness

Brightness on battery power

Enable to set screen brightness when the system is running on battery power.

Brightness on AC power

Enable to set screen brightness when the system is running on AC power.

EcoPower

Enable or disable EcoPower Feature in your panel. EcoPower can increase
the battery life of your system by reducing the display brightness when
appropriate.

By default,

Enable EcoPower

option is enabled.

Full Screen Logo

Enable or disable full screen logo.

By default, the option is not enabled.

Table 9. System setup options—Connection menu

Connection

Wireless Device Enable

WLAN

Enable or disable the internal WLAN device.

By default, the option enabled.

Bluetooth

Enable or disable the internal Bluetooth device

By default, the option enabled.

Enable UEFI Network Stack

Enable or disable UEFI Network Stack and controls the on-board LAN
Controller.

By default, the

Enable UEFI Network Stack

option is enabled.

HTTPs Boot Feature

HTTPs Boot

Enable or disable the HTTPs Boot feature.

By default, the

HTTPs Boot

option is disabled.

Table 10. System setup options—Power menu

Power

Battery configuration

Enables the system to run on battery during peak power usage hours. Use the
table

Custom Charge Start

and

Custom Charge Stop

, to prevent AC power

usage between certain times of each day.

By default, the

Adaptive

option is enabled.

Advanced Configuration

104

BIOS setup

Содержание D03T
























































































































Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды

Dell D03T, Руководство по обслуживанию

Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды