Dell D03T Скачать руководство пользователя страница 20

Страница: 20 / 119

External storage flexbay (Hard drive)

Removing the external hard-drive assembly

Prerequisites

1. Follow the procedure in

About this task

The following images indicate the location of the external hard-drive assembly and provide a visual representation of the
removal procedure.

Steps

1. Push the release button on the external-flexbay bracket to open the release latch.
2. Hold the release latch and slide the hard-drive assembly out of the external flexbay slot.

Installing the external hard-drive assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the external hard-drive assembly and provide a visual representation of the
installation procedure.

Removing and installing components

Содержание D03T
























































































































Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды

Dell D03T, Руководство по обслуживанию

Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды