Dell D03T Скачать руководство пользователя страница 17

Страница: 17 / 119

Front bezel

Removing the front bezel

Prerequisites

1. Follow the procedure in

Before working inside your computer

2. Remove the

side cover

About this task

The following images indicate the location of the front bezel and provide a visual representation of the removal procedure.

Steps

1. Pry the retention tabs to release the front bezel from the computer.
2. Slightly pull the front bezel and gently rotate to release the other tabs on the bezel from the slots in the chassis.
3. Remove the front bezel from the computer.

Installing the front bezel

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the front bezel and provide a visual representation of the installation procedure.

Removing and installing components

Содержание D03T
























































































































Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды

Dell D03T, Руководство по обслуживанию

Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды